REV. B
Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
a
ADM1023*
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700 World Wide Web Site: http://www.analog.com Fax: 781/326-8703 © Analog Devices, Inc., 2000 FUNCTIONAL BLOCK DIAGRAM
ON-CHIP TEMPERATURE
SENSOR
A-TO-D CONVERTER BUSY RUN/STANDBY
EXTERNAL DIODE OPEN-CIRCUIT
ADDRESS POINTER REGISTER ONE-SHOT REGISTER
CONVERSION RATE REGISTER
OFFSET REGISTERS
REMOTE TEMPERATURE HIGH-LIMIT REGISTERS
CONFIGURATION REGISTER
INTERRUPT MASKING
SMBUS INTERFACE LOCAL TEMPERATURE
LOW-LIMIT COMPARATOR
LOCAL TEMPERATURE HIGH-LIMIT COMPARATOR
REMOTE TEMPERATURE LOW-LIMIT COMPARATOR
REMOTE TEMPERATURE HIGH-LIMIT COMPARATOR REMOTE TEMPERATURE
VALUE REGISTERS LOCAL TEMPERATURE
VALUE REGISTER
STATUS REGISTER
NC VDD NC GND GND NC NC NC SDATA SCLK ADD0 ADD1
ALERT STBY D+
D– REMOTE TEMPERATURE
LOW-LIMIT REGISTERS LOCAL TEMPERATURE HIGH-LIMIT REGISTER LOCAL TEMPERATURE
LOW-LIMIT REGISTER
ANALOG MUX
NC = NO CONNECT
ADM1023
ACPI-Compliant High-Accuracy Microprocessor System Temperature Monitor
FEATURES
Next Generation Upgrade to ADM1021 On-Chip and Remote Temperature Sensing Offset Registers for System Calibration 1ⴗC Accuracy and Resolution on Local Channel 0.125ⴗC Resolution/1ⴗC Accuracy on Remote Channel Programmable Over/Under Temperature Limits Programmable Conversion Rate
Supports System Management Bus (SMBus) Alert 2-Wire SMBus Serial Interface
200 A Max Operating Current (0.25 Conversions/
Seconds)
1 A Standby Current 3 V to 5.5 V Supply
Small 16-Lead QSOP Package APPLICATIONS
Desktop Computers Notebook Computers Smart Batteries Industrial Controllers Telecomms Equipment Instrumentation
PRODUCT DESCRIPTION
The ADM1023 is a two-channel digital thermometer and under/
over temperature alarm, intended for use in personal computers and other systems requiring thermal monitoring and management.
Optimized for the Pentium® III; the higher accuracy offered allows systems designers to safely reduce temperature guard banding and increase system performance. The device can measure the temperature of a microprocessor using a diode-con- nected PNP transistor, which may be provided on-chip in the case of the PentiumIII or similar processors, or can be a low cost discrete NPN/PNP device such as the 2N3904/2N3906.
A novel measurement technique cancels out the absolute value of the transistor’s base emitter voltage, so that no calibration is required. The second measurement channel measures the output of an on-chip temperature sensor, to monitor the tem- perature of the device and its environment.
The ADM1023 communicates over a 2-wire serial interface compatible with SMBusstandards. Under and over tempera- ture limits can be programmed into the device over the serial bus, and an ALERT output signals when the on-chip or remote temperature is out of range. This output can be used as an interrupt, or as an SMBus alert.
*Patents pending.
Pentium is a registered trademark of Intel Corporation.
ADM1023–SPECIFICATIONS
(TA = TMIN to TMAX1, VDD = 3.0 V to 3.6 V, unless otherwise noted)Parameter Min Typ Max Unit Test Conditions/Comments
POWER SUPPLY AND ADC
Temperature Resolution, Local Sensor 1 °C Guaranteed No Missed Codes
Temperature Resolution, Remote Sensor 0.125 °C Guaranteed No Missed Codes
Temperature Error, Local Sensor –1.5 ±0.5 +1.5 °C TA = 60°C to 100°C
–3 ±1 +3 °C TA = 0°C to 120°C
Temperature Error, Remote Sensor –1 +1 °C TA, TD = 60°C to 100°C (Note 2)
–3 +3 °C TA, TD = 0°C to 120°C (Note 2)
Relative Accuracy 0.25 °C TA = 60°C to 100°C
Supply Voltage Range 3 3.6 V Note 3
Undervoltage Lockout Threshold 2.55 2.7 2.8 V VDD Input, Disables ADC, Rising Edge
Undervoltage Lockout Hysteresis 25 mV
Power-On Reset Threshold 0.9 1.7 2.2 V VDD, Falling Edge (Note 4)
POR Threshold Hysteresis 50 mV
Standby Supply Current 1 5 µA VDD = 3.3 V, No SMBus Activity
4 µA SCLK at 10 kHz
Average Operating Supply Current 130 200 µA 0.25 Conversions/Sec Rate
Autoconvert Mode, Averaged Over 4 Sec 225 330 µA 2 Conversions/Sec Rate
Conversion Time 65 115 170 ms From Stop Bit to Conversion
Complete (Both Channels) D+ Forced to D– + 0.65 V
Remote Sensor Source Current 120 205 300 µA High Level (Note 4)
7 12 16 µA Low Level (Note 4)
D-Source Voltage 0.7 V
Address Pin Bias Current (ADD0, ADD1) 50 µA Momentary at Power-On Reset
SMBus INTERFACE
Logic Input High Voltage, VIH 2.2 V VDD = 3 V to 5.5 V
STBY, SCLK, SDATA
Logic Input Low Voltage, VIL 0.8 V VDD = 3 V to 5.5 V
STBY, SCLK, SDATA
SMBus Output Low Sink Current 6 mA SDATA Forced to 0.6 V
ALERT Output Low Sink Current 1 mA ALERT Forced to 0.4 V
Logic Input Current, IIH, IIL –1 +1 µA
SMBus Input Capacitance, SCLK, SDATA 5 pF
SMBus Clock Frequency 100 kHz
SMBus Clock Low Time, tLOW 4.7 µs tLOW Between 10% Points
SMBus Clock High Time, tHIGH 4 ns tHIGH Between 90% Points
SMBus Start Condition Setup Time, tSU:STA 4.7 ns
SMBus Start Condition Hold Time, tHD:STA 4 ns Time from 10% of SDATA to 90%
of SCLK
SMBus Stop Condition Setup Time, tSU:STO 4 ns Time from 90% of SCLK to 10%
of SDATA
SMBus Data Valid to SCLK 250 ns Time for 10% or 90% of
Rising Edge Time, tSU:DAT SDATA to 10% of SCLK
SMBus Data Hold Time, tHD:DAT 0 µs
SMBus Bus Free Time, tBUF 4.7 µs Between Start/Stop Condition
SCLK Falling Edge to SDATA 1 µs Master Clocking in Data
Valid Time, tVD,DAT
SMBus Leakage Current 5 µA VDD = 0 V
NOTES
1TMAX = 120°C, TMIN = 0°C.
2TD is temperature of remote thermal diode; TA, TD = 60°C to 100°C.
3Operation at VDD = 5 V guaranteed by design, not production tested.
4Guaranteed by design, not production tested.
Specifications subject to change without notice.
REV. B
ABSOLUTE MAXIMUM RATINGS*
Positive Supply Voltage (VDD) to GND . . . –0.3 V to +6 V D+, ADD0, ADD1 . . . –0.3 V to VDD + 0.3 V D– to GND . . . –0.3 V to +0.6 V SCLK, SDATA, ALERT, STBY . . . –0.3 V to +6 V Input Current . . . ±50 mA Input Current, D– . . . ±1 mA ESD Rating, all pins (Human Body Model) . . . 2000 V Continuous Power Dissipation
Up to 70°C . . . 650 mW Derating Above 70°C . . . 6.7 mW/°C Operating Temperature Range . . . –55°C to +125°C Maximum Junction Temperature (TJ max) . . . 150°C Storage Temperature Range . . . –65°C to +150°C Lead Temperature (Soldering 10 sec) . . . 300°C IR Reflow Peak Temperature . . . 220°C
*Stresses above those listed under Absolute Maximum Ratings may cause perma- nent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
THERMAL CHARACTERISTICS 16-Lead QSOP Package
θJA = 105°C/W θJC = 39°C/W
ORDERING GUIDE
Temperature Package Package
Model Range Description Option
ADM1023ARQ 0°C to 120°C 16-Lead QSOP RQ-16
PIN FUNCTION DESCRIPTIONS Pin No. Mnemonic Description
1, 5, 9, NC No Connect.
13, 16
2 VDD Positive supply, 3 V to 5.5 V.
3 D+ Positive connection to remote tem-
perature sensor.
4 D– Negative connection to remote tem-
perature sensor.
6 ADD1 Three-state logic input, higher bit of device address.
7, 8 GND Supply 0 V connection.
10 ADD0 Three-state logic input, lower bit of device address.
11 ALERT Open-drain logic output used as interrupt or SMBus alert.
12 SDATA Logic input/output, SMBus serial data. Open-drain output.
14 SCLK Logic input, SMBus serial clock.
15 STBY Logic input selecting normal opera- tion (high) or standby mode (low).
PIN CONFIGURATION
TOP VIEW (Not to Scale)
16 15 14 13 12 11 10 9 1
2 3 4 5 6 7 8 GND
VDD
NC
ALERT D+
D– ADM1023 NC
GND ADD1 NC
NC ADD0 SDATA NC SCLK STBY
NC = NO CONNECT
P P S
tHD;STA
tSU;STA
tSU;DAT
tHIGH
tF
tHD;DAT tR tLOW
tHD;STA
tBUF S SCL
SDA
tSU;STO
Figure 1. Diagram for Serial Bus Timing
ADM1023 –Typical Performance Characteristics
LEAKAGE RESISTANCE – M⍀ 20
15
–25
100
TEMPERATURE ERROR – ⴗC
10 1
0
–10
–15
–20 10
5
–5
–30
D+ TO GND
D+ TO VDD
Figure 2. Temperature Error vs. Resistance from Track to VDD and GND
3
1
0 2
FREQUENCY – Hz 100
TEMPERATURE ERROR – ⴗC 4 5
1k 10k 100k 1M 10M 100M
250mV p-p REMOTE
100mV p-p REMOTE
Figure 3. Remote Temperature Error vs. Supply Noise Frequency
5
4
3
1
0 2
FREQUENCY – Hz 1
TEMPERATURE ERROR – ⴗC
10 1k 10k 10M 100M
6 7 8 9
100 100k 1M
50mV p-p 100mV p-p
25mV p-p
Figure 4. Temperature Error vs. Common-Mode Noise Frequency
1
–1
–3 –2
TEMPERATURE – ⴗC 50
ERROR –ⴗC
2 3
60 70 80 90 110 120
0
100 LOWER SPEC LEVEL UPPER SPEC LEVEL
Figure 5. Temperature Error of ADM1023 vs. Pentium III Temperature
CAPACITANCE – nF –1
2
TEMPERATURE ERROR – ⴗC
12 14
4 6 8 10 12 14 16 18 20 22 24
0 2 4 6 8 10
Figure 6. Temperature Error vs. Capacitance Between D+
and D–
SCLK FREQUENCY – kHz 1
SUPPLY CURRENT – A
20
0
VDD = 3.3V
5 10 25 50 75 100 250 500 750 1000 40
60 70
50
30
10
VDD = 5V
Figure 7. Standby Supply Current vs. SCLK Frequency
REV. B
4
0 2
FREQUENCY – Hz
TEMPERATURE ERROR – ⴗC
10mV p-p
100k 1M 10M 100M 1G
1 3
Figure 8. Temperature Error vs. Differential-Mode Noise Frequency
CONVERSION RATE – Hz 250
0.125
SUPPLY CURRENT – A
0.25 0.5 8
300 350 400 550
4 0.0625
450 500
200 150 100 50
5 VOLTS 3.3 VOLTS
2 1
Figure 9. Operating Supply Current vs. Conversion Rate, VDD = 5 V and 3 V
FUNCTIONAL DESCRIPTION
The ADM1023 contains a two-channel, A-to-D converter with special input-signal conditioning to enable operation with remote and on-chip diode temperature sensors. When the ADM1023 is operating normally, the A-to-D converter operates in a free-running mode. The analog input multiplexer alternately selects either the on-chip temperature sensor to measure its local temperature, or the remote temperature sensor. These signals are digitized by the ADC and the results are stored in the Local and Remote Temperature Value Registers. Only the eight most significant bits of the local temperature value are stored as an 8-bit binary word. The remote temperature value is stored as an 11-bit, binary word in two registers. The eight MSBs are stored in the Remote Temperature Value High Byte Register at address 01h. The three LSBs are stored, left-justified, in the Remote Temperature Value High Byte Register at address 10h.
Error sources such as PCB track resistance and clock noise can introduce offset errors into measurements on the Remote Channel. To achieve the specified accuracy on this channel, these offsets must be removed, and two Offset Registers are provided for this purpose at addresses 11h and 12h.
An offset value may automatically be added to or subtracted from the measurement by writing an 11 bit, two’s complement
value to registers 11h (high byte) and 12h (low byte, left- justified).
The offset registers default to zero at power-up and will have no effect if nothing is written to them.
The measurement results are compared with Local and Remote, High and Low Temperature Limits, stored in six on-chip Limit Registers. As with the measured value, the local temperature limits are stored as 8-bit values and the remote temperature limits as 11-bit values. Out-of-limit comparisons generate flags that are stored in the status register, and one or more out-of-limit results will cause the ALERT output to pull low.
Registers can be programmed, and the device controlled and configured, via the serial System Management Bus. The con- tents of any register can also be read back via the SMBus.
Control and configuration functions consist of:
• Switching the device between normal operation and standby mode.
• Masking or enabling the ALERT output.
• Selecting the conversion rate.
On initial power-up the remote and local temperature values default to –128°C. Since the device normally powers up convert- ing, a measure of local and remote temperature is made and these
0 20
SUPPLY VOLTAGE – V 0
SUPPLY CURRENT – A
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 40
60 80 100
–20
Figure 10. Standby Supply Current vs. Supply Voltage
TIME – Seconds
TEMPERATURE – ⴗC
0 25 50 75 100 125
REMOTE TEMPERATURE
INT
TEMPERATURE
0 1 2 3 4 5 6 7 8 9 10
Figure 11. Response to Thermal Shock
ADM1023
values are then stored before a comparison with the stored limits is made. However, if the part is powered up in standby mode (STBY pin pulled low), no new values are written to the register before a comparison is made. As a result, both RLOW and LLOW are tripped in the Status Register thus generating an ALERT output.
This may be cleared in one of two ways:
1. Change both the local and remote lower limits to –128°C and read the status register (which in turn clears the ALERT output).
2. Take the part out of standby and read the status register (which in turn clears the ALERT output). This will work only if the measured values are within the limit values.
MEASUREMENT METHOD
A simple method of measuring temperature is to exploit the nega- tive temperature coefficient of a diode, or the base-emitter voltage of a transistor, operated at constant current. Thus, the temperature may be obtained from a direct measurement of VBE where,
V nKT
q
I
BE I
C S
= × ln( )
(1) Unfortunately, this technique requires calibration to null out the effect of the absolute value of VBE, which varies from device to device.
The technique used in the ADM1023 is to measure the change in VBE when the device is operated at two different collector currents.
This is given by:
∆V nKT
q N
BE = × ln ( ) (2)
where:
K is Boltzmann’s constant
q is charge on the electron (1.6 × 10–19 Coulombs) T is absolute temperature in Kelvins
N is ratio of the two collector currents
n is the ideality factor of the thermal diode (TD)
To measure ∆VBE, the sensor is switched between operating cur- rents of I and NI. The resulting waveform is passed through a low-pass filter to remove noise, then to a chopper-stabilized ampli- fier that performs the functions of amplification and rectification of the waveform to produce a dc voltage proportional to ∆VBE. This voltage is measured by the ADC, which gives a temperature output in binary format. To further reduce the effects of noise, digital filtering is performed by averaging the results of 16 measurement cycles. Signal conditioning and measurement of the internal temperature sensor is performed in a similar manner.
Figure 12 shows the input signal conditioning used to measure the output of an external temperature sensor. This figure shows the external sensor as a substrate PNP transistor, provided for temperature monitoring on some microprocessors, but it could equally well be a discrete transistor. If a discrete transistor is used, the collector will not be grounded and should be linked to the base. To prevent ground noise from interfering with the measurement, the more negative terminal of the sensor is not referenced to ground, but is biased above ground by an inter- nal diode at the D– input. If the sensor is operating in a noisy environment, C1 may optionally be added as a noise filter. Its value is typically 2200 pF, but should be no more than 3000 pF. See the section on Layout Considerations for more information on C1.
SOURCES OF ERRORS ON THERMAL TRANSISTOR MEASUREMENT METHOD EFFECT OF IDEALITY FACTOR (n)
The effects of ideality factor (n) and beta (Beta) of the temperature measured by a thermal transistor are discussed below. For a ther- mal transistor implemented on a submicron process, such as the substrate PNP used on a Pentium III processor, the temperature errors due to the combined effect of the ideality factor and beta are shown to be less than 3°C. Equation 2 is optimized for a sub- strate PNP transistor (used as a thermal diode) usually found on CPUs designed on submicron CMOS processes such as the Pentium III Processor. There is a thermal diode on board each of these processors. The n in the Equation 2 represents the ideality factor of this thermal diode. This ideality factor is a measure of the deviation of the thermal diode from ideal behavior.
According to Pentium III Processor manufacturing specifica- tions, measured values of n at 100°C are:
nMIN = 1.0057 < nTYPICAL = 1.008 < nMAX = 1.0125 The ADM1023 takes this ideality factor into consideration when calculating temperature TTD of the thermal diode. The ADM1023 is optimized for nTYPICAL = 1.008; any deviation on n from this typical value causes a temperature error that is calculated below for the nMIN and nMAX of a Pentium III Processor at TTD = 100°C,
∆TMIN =1 0057 1 008× Kelvin+ °C = °C
1 008 273 15 100 0 85
. – .
. ( . ) – .
∆TMAX =1 0125 1 008× Kelvin+ °C = + °C
1 008 273 15 100 1 67
. – .
. ( . ) .
Thus, the temperature error due variation on n of the thermal diode for Pentium III Processor is about 2.5°C.
C1*
D+
D–
REMOTE SENSING TRANSISTOR
I N ⴛ I IBIAS
VDD
VOUT+
TO ADC VOUT–
BIAS
DIODE LOW-PASS FILTER fC = 65kHz
CAPACITOR C1 IS OPTIONAL. IT IS ONLY NECESSARY IN NOISY ENVIRONMENTS.
C1 = 2.2nF TYPICAL, 3nF MAX.
*
Figure 12. Input Signal Conditioning
REV. B
In general, this additional temperature error of the thermal diode measurement due to deviations on n from its typical value is given by,
∆T n
Kelvin TTD TTD C
= – . × + °
.1 008 ( . ),
1 008 273 15 where is in
BETA OF THERMAL TRANSISTOR ()
On Figure 12, the thermal diode is a substrate PNP transistor where the emitter current is being forced into the device. The derivation of Equation 2 above assumed that the collector cur- rents scaled by “N” as the emitter currents were also scaled by
“N.” In other words, this assumes that beta (β) of the transistor is constant for various collector currents. The plot below shows typical beta variation versus collector current for Pentium III Processors at 100°C. The maximum beta is 4.5 and varies less than 1% over the collector current range from 7 µA to 300 µA.
⌬
7 300

IC (mA)
MAX < 4.5
IC = I E
+1 IE
Figure 13. Variation of β with Collector Currents Expressing the collector current in terms of the emitter current, IC = IE [β/β + 1)] where β(300 µA) = β(7 µA)(1 + ε ), ε = ∆β/β and β = β (7 µA). Rewriting the equation for ∆VBE, to include the ideality factor “n” and beta “β” we have,
∆V nKT
q N
BE = × + × +
+ + ×
ln ( ) ( )
( )
1 1
1 1
ε β
ε β (3)
Beta variations of less than 1% (ε < 0.01) contribute to tempera- ture errors of less than 0.4°C.
TEMPERATURE DATA FORMAT
One LSB of the ADC corresponds to 0.125°C, so the ADM1023 can measure from 0°C to 127.875°C. The temperature data for- mat is shown in Tables I and II.
Table I. Temperature Data Format (Local Temperature and Remote Temperature High Byte)
Temperature (ⴗC) Digital Output
0 0 000 0000
1 0 000 0001
10 0 000 1010
25 0 001 1001
50 0 011 0010
75 0 100 1011
100 0 110 0100
125 0 111 1101
127 0 111 1111
Note: The ADM1023 differs from the ADM1021 in that the tem- perature resolution of the remote channel is improved from 1°C to 0.125°C, but it cannot measure temperatures below 0°C. If negative temperature measurement is required, the ADM1021 should be used.
The results of the local and remote temperature measurements are stored in the local and remote temperature value registers, and are compared with limits programmed into the local and remote high and low limit registers.
Table II. Extended Temperature Resolution (Remote Temperature Low Byte)
Extended Remote Temperature Resolution (ⴗC) Low Byte
0.000 0000 0000
0.125 0010 0000
0.250 0100 0000
0.375 0110 0000
0.500 1000 0000
0.625 1010 0000
0.750 1100 0000
0.875 1110 0000
REGISTER FUNCTIONS
The ADM1023 contains registers that are used to store the results of remote and local temperature measurements, high and low temperature limits, and to configure and control the device.
A description of these registers follows, and further details are given in Tables III to VII. It should be noted that most of the ADM1023’s registers are dual port, and have different addresses for read and write operations. Attempting to write to a read address, or to read from a write address, will produce an invalid result. Register addresses above 14h are reserved for future use or used for factory test purposes and should not be written to.
Address Pointer Register
The Address Pointer Register itself does not have, nor does it require, an address, as it is the register to which the first data byte of every Write operation is written automatically. This data byte is an address pointer that sets up one of the other registers for the second byte of the Write operation, or for a subsequent read operation.
Value Registers
The ADM1023 has three registers to store the results of Local and Remote temperature measurements. These registers are written to by the ADC and can only be read over the SMBus.
The Offset Register
Two offset registers are provided at addresses 11h and 12h.
These are provided so that the user may remove errors from the measured values of remote temperature. These errors may be introduced by clock noise and PCB track resistance.
The offset value is stored as an 11-bit, two’s complement value in Registers 11h (high byte) and 12h (low byte, left-justified).
The value of the offset is negative if the MSB of 11h is 1 and is positive if the MSB of 11h is 0. This value is added to the remote temperature. These registers default to zero at power-up and will have no effect if nothing is written to them. The offset regis- ter can accept values from –128.875°C to +127.875°C. The ADM1023 detects overflow so the remote temperature value register won’t wrap around +127°C or –128°C. Table IV con- tains a set of example offset values.
ADM1023
Table IV.
Remote Remote Temperature Temperature Offset Registers Offset (Including (Without
11h 12h Value Offset) Offset)
1111 1100 0000 0000 –4°C 14°C 18°C 1111 1111 0000 0000 –1°C 17°C 18°C 1111 1111 1110 0000 –0.125°C 17.875°C 18°C 0000 0000 0000 0000 0°C 18°C 18°C 0000 0000 0010 0000 +0.125°C 18.125°C 18°C 0000 0001 0000 0000 +1°C 19°C 18°C 0000 0100 0000 0000 +4°C 22°C 18°C Status Register
Bit 7 of the Status Register indicates that the ADC is busy con- verting when it is high. Bits 6 to 3 are flags that indicate the results of the limit comparisons.
If the local and/or remote temperature measurement is above the corresponding high temperature limit, or below the corre- sponding low temperature limit, one or more of these flags will be set. Bit 2 is a flag that is set if the remote temperature sensor is open-circuit. These five flags are NOR’d together, so that if any of them are high, the ALERT interrupt latch will be set and the ALERT output will go low. Reading the Status Register will clear the five flag bits, provided the error conditions that caused the flags to be set have gone away. While a limit comparator is tripped due to a value register containing an out-of-limit measurement, or the sensor is open-circuit, the corresponding flag bit cannot be reset. A flag bit can only be reset if the corre- sponding value register contains an in-limit measurement, or the sensor is good.
The ALERT interrupt latch is not reset by reading the Status Register, but will be reset when the ALERT output has been serviced by the master reading the device address, provided the error condition has gone away and the Status Register flag bits have been reset.
Table V. Status Register Bit Assignments Bit Name Function
7 BUSY 1 When ADC Converting.
6 LHIGH* 1 When Local High Temp Limit Tripped.
5 LLOW* 1 When Local Low Temp Limit Tripped.
4 RHIGH* 1 When Remote High Temp Limit Tripped.
3 RLOW* 1 When Remote Low Temp Limit Tripped.
2 OPEN* 1 When Remote Sensor Open-Circuit.
1–0 Reserved.
*These flags stay high until the status register is read or they are reset by POR.
Configuration Register
Two bits of the configuration register are used. If Bit 6 is 0, which is the power-on default, the device is in operating mode with the ADC converting. If Bit 6 is set to 1, the device is in standby mode and the ADC does not convert. Standby mode can also be selected by taking the STBY pin low. In standby mode the values of remote and local temperature remain at the value they were before the part was placed in standby.
Bit 7 of the configuration register is used to mask the ALERT output. If Bit 7 is 0, which is the power-on default, the ALERT output is enabled. If Bit 7 is set to 1, the ALERT output is disabled.
Table III. List of ADM1023 Registers
READ Address (Hex) WRITE Address (Hex) Name Power-On Default
Not Applicable Not Applicable Address Pointer Undefined
00 Not Applicable Local Temperature Value 1000 0000 (80h) (–128°C)
01 Not Applicable Remote Temperature Value High Byte 1000 0000 (80h) (–128°C)
02 Not Applicable Status Undefined
03 09 Configuration 0000 0000 (00h)
04 0A Conversion Rate 0000 0010 (02h)
05 0B Local Temperature High Limit 0111 1111 (7Fh) (+127°C)
06 0C Local Temperature Low Limit 1100 1001 (C9h) (–55°C)
07 0D Remote Temperature High Limit High Byte 0111 1111 (7Fh) (+127°C)
08 0E Remote Temperature Low Limit High Byte 1100 1001 (C9h) (–55°C)
Not Applicable 0F1 One-Shot
10 Not Applicable Remote Temperature Value Low Byte 0000 0000
11 11 Remote Temperature Offset High Byte 0000 0000
12 12 Remote Temperature Offset Low Byte 0000 0000
13 13 Remote Temperature High Limit Low Byte 0000 0000
14 14 Remote Temperature Low Limit Low Byte 0000 0000
19 Not Applicable Reserved 0000 0000
20 21 Reserved Undefined
FE Not Applicable Manufacturer Device ID 0100 0001 (41h)
FF Not Applicable Die Revision Code 0011 xxxx (3xh)
NOTE
1Writing to address 0F causes the ADM1023 to perform a single measurement. It is not a data register as such and it does not matter what data is written to it.
REV. B
Table VI. Configuration Register Bit Assignments Power-On
Bit Name Function Default
7 MASK1 0 = ALERT Enabled 0
1 = ALERT Masked
6 RUN/STOP 0 = Run 0
1 = Standby
5–0 Reserved 0
Conversion Rate Register
The lowest three bits of this register are used to program the conversion rate by dividing the ADC clock by 1, 2, 4, 8, 16, 32, 64, or 128, to give conversion times from 125 ms (Code 07h) to 16 seconds (Code 00h). This register can be written to and read back over the SMBus. The higher five bits of this register are unused and must be set to zero. Use of slower conversion times greatly reduces the device power consumption, as shown in Table VII.
Table VII. Conversion Rate Register Codes Average Supply Current Data Conversion/sec A Typ at VCC = 3.3 V
00h 0.0625 150
01h 0.125 150
02h 0.25 150
03h 0.5 150
04h 1 150
05h 2 150
06h 4 160
07h 8 180
08h to FFh Reserved Limit Registers
The ADM1023 has six limit registers to store local and remote, high and low temperature limits. These registers can be written to and read back, over the SMBus. The high limit registers per- form a > comparison while the low limit registers perform a
< comparison. For example, if the high limit register is programmed as a limit of 80°C, measuring 81°C will result in an alarm condi- tion. Even though the temperature range is 0 to 127°C, it is possible to program the Limit Register with negative values.
This is for backwards-compatibility with the ADM1021.
One-Shot Register
The one-shot register is used to initiate a single conversion and comparison cycle when the ADM1023 is in standby mode, after which the device returns to standby. This is not a data register as such and it is the write operation that causes the one-shot conver- sion. The data written to this address is irrelevant and is not stored.
SERIAL BUS INTERFACE
Control of the ADM1023 is carried out via the serial bus. The ADM1023 is connected to this bus as a slave device, under the control of a master device.
ADDRESS PINS
In general, every SMBus device has a 7-bit device address (except for some devices that have extended, 10-bit addresses). When the master device sends a device address over the bus, the slave device with that address will respond. The ADM1023 has two address pins, ADD0 and ADD1, to allow selection of the device address, so that several ADM1023s can be used on the same bus,
and/or to avoid conflict with other devices. Although only two address pins are provided, these are three-state, and can be grounded, left unconnected, or tied to VDD, so that a total of nine different addresses are possible, as shown in Table VIII.
It should be noted that the state of the address pins is only sampled at power-up, so changing them after power-up will have no effect.
Table VIII. Device Addresses
ADD0 ADD1 Device Address
0 0 0011 000
0 NC 0011 001
0 1 0011 010
NC 0 0101 001
NC NC 0101 010
NC 1 0101 011
1 0 1001 100
1 NC 1001 101
1 1 1001 110
ADD0, ADD1 sampled at power-up only.
The serial bus protocol operates as follows:
1. The master initiates data transfer by establishing a START condi- tion, defined as a high-to-low transition on the serial data line SDATA, while the serial clock line SCLK remains high. This indicates that an address/data stream will follow. All slave peripherals connected to the serial bus respond to the START condition and shift in the next eight bits, consisting of a 7-bit address (MSB first) plus an R/W bit, which determines the direction of the data transfer, i.e., whether data will be written to or read from the slave device.
The peripheral whose address corresponds to the transmitted address responds by pulling the data line low during the low period before the ninth clock pulse, known as the Acknowledge Bit. All other devices on the bus now remain idle while the selected device waits for data to be read from or written to it.
If the R/W bit is a 0, the master will write to the slave device. If the R/W bit is a 1, the master will read from the slave device.
2. Data is sent over the serial bus in sequences of nine clock pulses, eight bits of data followed by an acknowledge bit from the slave device. Transitions on the data line must occur during the low period of the clock signal and remain stable during the high period, as a low-to-high transition when the clock is high may be interpreted as a STOP signal. The number of data bytes that can be transmitted over the serial bus in a single READ or WRITE operation is limited only by what the master and slave devices can handle.
3. When all data bytes have been read or written, stop condi- tions are established. In WRITE mode, the master will pull the data line high during the 10th clock pulse to assert a STOP condition. In READ mode, the master device will override the acknowledge bit by pulling the data line high during the low period before the ninth clock pulse. This is known as No Acknowledge. The master will then take the data line low during the low period before the 10th clock pulse, then high during the 10th clock pulse to assert a STOP condition.
Any number of bytes of data may be transferred over the serial bus in one operation, but it is not possible to mix read and write in one operation, because the type of operation is determined at the beginning and cannot subsequently be changed without starting a new operation.
ADM1023
In the case of the ADM1023, write operations contain either one or two bytes, while read operations contain one byte and perform the following functions:
To write data to one of the device data registers or read data from it, the Address Pointer Register must be set so that the correct data register is addressed, then data can be written into that register or read from it. The first byte of a write operation always contains a valid address that is stored in the Address Pointer Register. If data is to be written to the device, the write operation contains a second data byte that is written to the regis- ter selected by the address pointer register.
This is illustrated in Figure 14. The device address is sent over the bus followed by R/W set to 0. This is followed by two data bytes. The first data byte is the address of the internal data register to be written to, which is stored in the Address Pointer Register.
The second data byte is the data to be written to the internal data register.
When reading data from a register there are two possibilities:
1. If the ADM1023’s Address Pointer Register value is unknown, or not the desired value, it is first necessary to set it to the correct value before data can be read from the desired data register. This is done by performing a write to the ADM1023
as before, but only the data byte containing the register read address is sent, as data is not to be written to the register.
This is shown in Figure 15.
A read operation is then performed consisting of the serial bus address, R/W bit set to 1, followed by the data byte read from the data register. This is shown in Figure 15.
2. If the Address Pointer Register is known to be already at the desired address, data can be read from the corresponding data register without first writing to the Address Pointer Reg- ister, so Figure 15 can be omitted.
NOTES
1. Although it is possible to read a data byte from a data register without first writing to the Address Pointer Register, if the Address Pointer Register is already at the correct value, it is not possible to write data to a register without writing to the Address Pointer Register, because the first data byte of a write is always written to the Address Pointer Register.
2. Do not forget that ADM1023 registers have different addresses for read and write operations. The write address of a register must be written to the Address Pointer if data is to be written to that register, but it is not possible to read data from that address. The read address of a register must be written to the Address Pointer before data can be read from that register.
R/W 0
SCLK
SDATA 1 0 1 1 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
ACK. BY ADM1023 START BY
MASTER
1 9 1
ACK. BY ADM1023
9
D7 D6 D5 D4 D3 D2 D1 D0
ACK. BY ADM1023
STOP BY MASTER
1 9
SCLK (CONTINUED)
SDATA (CONTINUED)
FRAME 3 DATA BYTE FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
Figure 14. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register
R/W 0
SCLK
SDATA 1 0 1 1 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0
ACK. BY ADM1023 START BY
MASTER
1 9 1
ACK. BY ADM1023
9
FRAME 1 SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
STOP BY MASTER
Figure 15. Writing to the Address Pointer Register Only
R/W SCLK
SDATA D7 D6 D5 D4 D3 D2 D1 D0
NO ACK.
BY MASTER START BY
MASTER
9 1
ACK. BY ADM1023
9
FRAME 1 SERIAL BUS ADDRESS BYTE
STOP BY MASTER
A6 A5 A4 A3 A2 A1 A0
FRAME 2 DATA BYTE FROM ADM1023 1
Figure 16. Reading Data from a Previously Selected Register
REV. B
ALERT OUTPUT
The ALERT output goes low whenever an out-of limit mea- surement is detected, or if the remote temperature sensor is open-circuit. It is an open-drain and requires a 10 kΩ pull-up to VDD. Several ALERT outputs can be wire-ANDED together, so that the common line will go low if one or more of the ALERT outputs goes low.
The ALERT output can be used as an interrupt signal to a pro- cessor, or it may be used as an SMBALERT. Slave devices on the SMBus normally cannot signal to the master they want to talk, but the SMBALERT function allows them to do so.
One or more ALERT outputs are connected to a common SMBALERT line connected to the master. When the SMBALERT line is pulled low by one of the devices, the following procedure occurs as illustrated in Figure 17.
MASTER RECEIVES SMBALERT
MASTER SENDS ARA AND READ
COMMAND DEVICE SENDS
ITS ADDRESS NO START ALERT RESPONSE ADDRESS RD ACK DEVICE ADDRESS ACK STOP
Figure 17. Use of SMBALERT 1. SMBALERT pulled low.
2. Master initiates a read operation and sends the Alert Response Address (ARA = 0001 100). This is a general call address that must not be used as a specific device address.
3. The device whose ALERT output is low responds to the Alert Response Address and the master reads its device address.
The address of the device is now known and it can be inter- rogated in the usual way.
4. If more than one device’s ALERT output is low, the one with the lowest device address, will have priority, in accordance with normal SMBus arbitration.
5. Once the ADM1023 has responded to the Alert Response Address, it will reset its ALERT output, provided that the error condition that caused the ALERT no longer exists. If the SMBALERT line remains low, the master will send ARA again, and so on until all devices whose ALERT outputs were low have responded.
LOW POWER STANDBY MODES
The ADM1023 can be put into a low power standby mode using hardware or software, that is, by taking the STBY input low, or by setting Bit 6 of the Configuration Register. When STBY is high, or Bit 6 is low, the ADM1023 operates normally. When STBY is pulled low or Bit 6 is high, the ADC is inhibited, any conversion in progress is terminated without writing the result to the correspond- ing value register.
The SMBus is still enabled. Power consumption in the standby mode is reduced to less than 10µA if there is no SMBus activ- ity, or 100µA if there are clock and data signals on the bus.
These two modes are similar but not identical. When STBY is low, conversions are completely inhibited. When Bit 6 is set but STBY is high, a one-shot conversion of both channels can be initiated by writing any data value to the One-Shot Register (Address 0Fh).
SENSOR FAULT DETECTION
The ADM1023 has a fault detector at the D+ input that detects if the external sensor diode is open-circuit. This is a simple voltage comparator that trips if the voltage at D+ exceeds VCC – 1 V (typical). The output of this comparator is checked when a conver- sion is initiated, and sets Bit 2 of the Status Register if a fault is detected.
If the remote sensor voltage falls below the normal measuring range, for example, due to the diode being short-circuited, the ADC will output –128°C (1000 0000 000). Since the normal operating temperature range of the device only extends down to 0°C, this output code will never be seen in normal operation, so it can be interpreted as a fault condition.
In this respect, the ADM1023 differs from and improves upon competitive devices that output zero if the external sensor goes short-circuit. These devices can misinterpret a genuine 0°C mea- surement as a fault condition.
If the external diode channel is not being used and is shorted out, the resulting ALERT may be cleared by writing 80h (–128°C) to the low limit register.
APPLICATIONS INFORMATION FACTORS AFFECTING ACCURACY Remote Sensing Diode
The ADM1023 is designed to work with substrate transistors built into processors, or with discrete transistors. Substrate tran- sistors will generally be PNP types with the collector connected to the substrate. Discrete types can be either PNP or NPN, con- nected as a diode (base shorted to collector). If an NPN transistor is used then the collector and base are connected to D+ and the emitter to D–. If a PNP transistor is used, the collector and base are connected to D– and the emitter to D+.
The user has no choice in the case of substrate transistors, but if a discrete transistor is used, the best accuracy will be obtained by choosing devices according to the following criteria:
1. Base-emitter voltage greater than 0.25 V at 6 µA, at the high- est operating temperature.
2. Base-emitter voltage less than 0.95 V at 100 µA, at the lowest operating temperature.
3. Base resistance less than 100 ⍀.
4. Small variation in hfe (say 50 to 150) which indicates tight control of VBE characteristics.
Transistors such as 2N3904, 2N3906 or equivalents in SOT-23 package are suitable devices to use.
Thermal Inertia and Self-Heating
Accuracy depends on the temperature of the remote-sensing diode and/or the internal temperature sensor being at the same temperature as that being measured; and a number of factors can affect this. Ideally, the sensor should be in good thermal contact with the part of the system being measured, for example the processor. If it is not, the thermal inertia caused by the mass of the sensor will cause a lag in the response of the sensor to a temperature change. In the case of the remote sensor this should not be a problem, as it will be either a substrate transistor in the processor or a small package device such as SOT-23 placed in close proximity to it.
The on-chip sensor, however, will often be remote from the pro- cessor and will only be monitoring the general ambient temperature
C00058–0–9/00 (rev. B)PRINTED IN U.S.A.
ADM1023
around the package. The thermal time constant of the QSOP-16 package is about 10 seconds.
In practice, the package will have electrical, and hence thermal, connection to the printed circuit board, so the temperature rise due to self-heating will be negligible.
LAYOUT CONSIDERATIONS
Digital boards can be electrically noisy environments, and the ADM1023 is measuring very small voltages from the remote sensor, so care must be taken to minimize noise induced at the sensor inputs. The following precautions should be taken:
1. Place the ADM1023 as close as possible to the remote sensing diode. Provided that the worst noise sources such as clock generators, data/address buses and CRTs are avoided, this distance can be four to eight inches.
2. Route the D+ and D– tracks close together, in parallel, with grounded guard tracks on each side. Provide a ground plane under the tracks if possible.
3. Use wide tracks to minimize inductance and reduce noise pickup. 10 mil track minimum width and spacing is recommended.
10MIL 10MIL 10MIL 10MIL 10MIL 10MIL 10MIL GND
D+
D–
GND
Figure 18. Arrangement of Signal Tracks 4. Try to minimize the number of copper/solder joints, which
can cause thermocouple effects. Where copper/solder joints are used, make sure that they are in both the D+ and D–
path and at the same temperature.
Thermocouple effects should not be a major problem as 1°C corresponds to about 240µV, and thermocouple voltages are about 3µV/°C of temperature difference. Unless there are two thermocouples with a big temperature differential between them, thermocouple voltages should be much less than 240µV.
5. Place a 0.1µF bypass capacitor close to the VDD pin and 2200 pF input filter capacitors across D+, D– close to the ADM1023.
6. If the distance to the remote sensor is more than eight inches, the use of twisted pair cable is recommended. This will work up to about 6 to 12 feet.
7. For really long distances (up to 100 feet), use shielded twisted pair such as Belden #8451 microphone cable. Connect the twisted pair to D+ and D– and the shield to GND close to the ADM1023. Leave the remote end of the shield uncon- nected to avoid ground loops.
Because the measurement technique uses switched current sources, excessive cable and/or filter capacitance can affect the measure- ment. When using long cables, the filter capacitor may be reduced or removed.
Cable resistance can also introduce errors. 1Ω series resistance introduces about 1°C error.
APPLICATION CIRCUITS
Figure 19 shows a typical application circuit for the ADM1023, using a discrete sensor transistor connected via a shielded, twisted pair cable. The pull-ups on SCLK, SDATA, and ALERT are required only if they are not already provided elsewhere in the system.
The SCLK and SDATA pins of the ADM1023 can be interfaced directly to the SMBus of an I/O chip. Figure 20 shows how the ADM1023 might be integrated into a system using this type of I/O controller.
ALERT
GND ADD0 D+
D–
ADM1023
OUT SCLK
SDATA
ADD1 VDD
I/O
SET TO REQUIRED ADDRESS
IN 3V TO 5.5V
2200pF
10k⍀ 10k⍀
TO CONTROL CHIP 10k⍀
0.1F
SHIELD 2N3904
Figure 19. Typical ADM1023 Application Circuit
USB 2 USB PORTS
ICH I/O CONTROLLER
HUB CD ROM
HARD DISK
SYSTEM MEMORY PROCESSOR
GMCH DISPLAY
DISPLAY CACHE
ADM1023
SCLK
SDATA
ALERT
D+
D–
SYSTEM BUS
PCI BUS PCI SLOTS
USB
FWH (FIRMWARE
HUB)
SUPER I/O SMBUS 2 IDE PORTS
Figure 20. Typical System Using ADM1023
OUTLINE DIMENSIONS Dimensions shown in inches and (mm).
16-Lead QSOP (RQ-16)
16 9
1 8
0.197 (5.00) 0.189 (4.80)
0.244 (6.20) 0.228 (5.79)
PIN 1 0.157 (3.99) 0.150 (3.81)
SEATING PLANE 0.010 (0.25)
0.004 (0.10)
0.012 (0.30) 0.008 (0.20) 0.025
(0.64) BSC 0.059 (1.50)
MAX
0.069 (1.75) 0.053 (1.35)
0.010 (0.20) 0.007 (0.18)
0.050 (1.27) 0.016 (0.41) 8ⴗ
0ⴗ
