ZAKRES AKREDYTACJI LABORATORIUM BADAWCZEGO SCOPE OF ACCREDITATION FOR TESTING LABORATORY Nr/No AB 1340

(1)

Niniejszy dokument jest załącznikiem do Certyfikatu Akredytacji Nr AB 1340 z dnia 28.07.2020 r.

Cykl akredytacji od 28.07.2020 r. do 29.07.2024 r.

Status akredytacji oraz aktualność zakresu akredytacji można potwierdzić na stronie internetowej PCA www.pca.gov.pl This document is an annex to accreditation certificate No AB 1340 of 28.07.2020

Accreditation cycle from 28.07.2020 to 29.07.2024

The status of accreditation and validity of the scope of accreditation can be confirmed at PCA website www.pca.gov.pl

Issue No 12, 12 of 15.07.2021 1/22

ZAKRES AKREDYTACJI

LABORATORIUM BADAWCZEGO

SCOPE OF ACCREDITATION FOR TESTING LABORATORY Nr/No AB 1340

wydany przez / issued by POLSKIE CENTRUM AKREDYTACJI 01-382 Warszawa, ul. Szczotkarska 42 Wydanie/Issue 12 z/of 12 z/of 15.07.2021

Wersja strony/Page version: A Nazwa i adres / Name and address

Institute for Research and Certification OBAC Ltd.

Łabędzka street 21 44-121 Gliwice

LABOREx Laboratory

Aronii street 4 44-102 Gliwice, Poland

Kod identyfikacyjny /

Identification code ^*) Dziedzina i przedmiot badań / Field of testing and item:

- A/13 - Badania akustyczne i hałasu – w tym spowodowanego przez drgania maszyn / Acoustic and vibration tests of Machinery and devices,

- E/6; E/13 - Badania elektryczne wyrobów elektrycznych, wyposażenia maszyn / Electric tests of electric products and machinery equipment,

- G/9 - Badania dotyczące inżynierii środowiska – hałas w środowisku pracy, hałas pochodzący od instalacji i urządzeń przemysłowych / Tests concerning environmental engineering – noise in workplace, noise generated by industrial instalation and devices

- H/21 - Badania ogniowe wyrobów z tworzyw sztucznych i gumy / Fire tests of plastic and rubber products - J/6; J/8; J/13; J/21 - Badania mechaniczne wyrobów i wyposażenia elektrycznego, wyrobów konstrukcyjnych i wyposażenia

maszyn, wyrobów z tworzyw sztucznych i gumy, pojazdów / Mechanical tests of products and electric equipment , construction products and machine equipment, plastic and rubber products, vehicle - N/6 - Badania właściwości fizycznych wyrobów i wyposażenia elektrycznego, wyrobów konstrukcyjnych i

wyposażenia maszyn, wyrobów z tworzyw sztucznych i gumy, sprzętu sportowego i rekreacyjnego / Tests of physical properties and electric equipment, construction products, machine devices, plastic and rubber products, sport equipment.

AB 1340

(2)

Edition no 12,15.07.2021 2/22 Laboratory of Electric Tests

Tested objects/Group of objects

Tested features and test/

measurement methods

Standards and/or documented testing procedures Electrical equipment for use in

potentially explosive atmospheres

Geometric linear dimensions

Method: direct PN-EN IEC 60079-0:2018-09

Resistance to impact

Range: Impact energy of up to 20J

PN-EN IEC 60079-0:2018-09 Resistance to drop-test impact PN-EN IEC 60079-0:2018-09 Thermal tests, temperatures and

temperature rise of up to +450°C PN-EN IEC 60079-0:2018-09 Thermal endurance to heat

Range: up to 180°C

PN-EN IEC 60079-0:2018-09 Thermal endurance to cold

Range: down to -75°C

PN-EN IEC 60079-0:2018-09

Cable glands PN-EN IEC 60079-0:2018-09

PN-G-50003:2003 Electrical equipment for

potentially

explosive atmospheres – Equipment protection by flameproof enclosures “d” – Cemented joints and sealed with cement

Method: direct PN-EN 60079-1:2014-12

Explosion pressure, reference pressure Range: up to 3 MPa

Method: Measurement of maximum explosion pressure

PN-EN 60079-1:2014-12

Ability of the enclosure to withstand pressure

Range: up to 3 MPa

Method: static pressurization

PN-EN 60079-1:2014-12

Protection against non-transmission of explosion

PN-EN 60079-1:2014-12 Flameproof cable glands

Range: up to 3 MPa, Torque of up to 150

Nm

PN-EN 60079-1:2014-12

Electrical equipment for potentially

explosive atmospheres – Equipment protection by pressurized enclosure “p”

Geometric linear dimensions Method: direct

PN-EN 60079-2:2015-02 Ability of the enclosure to withstand

pressure

Range: up to 3 MPa

PN-EN 60079-2:2015-02

Enclosure tightness Range: up to 3 MPa

PN-EN 60079-2:2015-02

Containment system infallibility Range: up to 3 MPa

PN-EN 60079-2:2015-02

explosive atmospheres – Equipment protection by powder filling “q”

PN-EN 60079-5:2015-08 Ability of the enclosure to withstand

pressure

PN-EN 60079-5:2015-08 IP degree of protection

Range of IP: 1X, 2X, 5X, 6X, X4, X5, X6, X7, X8

PN-EN 60079-5:2015-08

Thermal tests, temperatures and

temperature rise of up to 450°C PN-EN 60079-5:2015-08

Wersja strony: A

(3)

Edition no 12,15.07.2021 3/22 Tested objects/Group of objects Tested features and test/

measurement methods Standards and/or documented testing procedures Explosive atmospheres

Equipment protection by liquid immersion "o"

Type tests:

- Overpressure testing of sealed housings

- Reduced pressure testing of sealed housings

- Overpressure testing of unsealed casings

- Maximum temperature

- Switching studies Routine tests:

- Sealed housings - Unsealed housings

PN-EN 60079-6:2016-02

explosive atmospheres – Equipment protection by increased

safety “e”

PN-EN 60079-7:2016-02 +A1:2018-03

Insulation dielectric strength

Range: alternating voltage of up to 20 kV

PN-EN 60079-7:2016-02 +A1:2018-03

explosive atmospheres –

Equipment protection by intrinsic safety “i”

Method: direct PN-EN 60079-11:2012

Creepage distances and clearances Direct measurement

PN-EN 60079-11:2012 Insulation dielectric strength

PN-EN 60079-11:2012

Capacity of cells and batteries Resistance of cells and batteries to shortcircuit

PN-EN 60079-11:2012

Mechanical resistance of casting compound

PN-EN 60079-11:2012 Transformer insulation resistance PN-EN 60079-11: 2012 Spark-initiated ignition attempt PN-EN 60079-11 :2012 Electrical equipment for

potentially

explosive atmospheres – Equipment protection by type of protection “n”

PN-EN IEC 60079-15:2019-06 Thermal endurance to heat

Range: up to 180°C PN-EN IEC 60079-15:2019-06 Resistance to drop-test impact PN-EN IEC 60079-15:2019-06 Insulation dielectric strength

PN-EN IEC 60079-15:2019-06

explosive atmospheres – Equipment protection by encapsulation “m”

Thermal tests, temperatures and

temperature rise of up to 450°C PN-EN 60079-18:2015-06 +A1:2018-02

Thermal endurance to heat

Range: up to 180°C PN-EN 60079-18:2015-06 +A1:2018-02

Thermal endurance to cold Range: down to -75°C

PN-EN 60079-18:2015-06 +A1:2018-02

Range: alternating voltage up to 20 kV

PN-EN 60079-18:2015-06 +A1:2018-02

Ability of the enclosure to withstand pressure

Range: up to 3 MPa

PN-EN 60079-18:2015-06 +A1:2018-02

Compound test, water absorption test PN-EN 60079-18:2015-06 +A1:2018-02

(4)

measurement methods

Standards and/or documented testing procedures Electrical equipment for

potentially

explosive atmospheres – Intrinsically safe electrical systems

PN-EN 60079-25:2011 Separation distances,

Direct measurement PN-EN 60079-25:2011

PN-EN 60079-25:2011

Capacity of cells and batteries Resistance of cells and batteries to shortcircuit

PN-EN 60079-25:2011

Mechanical resistance of casting compound

PN-EN 60079-25:2011 Transformer insulation resistance PN-EN 60079-25:2011 Electrical equipment for

potentially

explosive atmospheres – Equipment with equipment protection level (EPL) Ga

Resistance to impact

Range: impact energy of up to 20 J

PN-EN 60079-26:2015-04 Thermal tests, temperatures and

temperature rise of up to 450°C

PN-EN 60079-26:2015-04

explosive atmospheres – Equipment dust ignition protection

by enclosure “t”

IP degree of protection

Range of IP: 1X, 2X, 5X, 6X, X4, X5, X6,X7, X8

PN-EN 60079-31:2014-10 IEC 60079-31:2013 Resistance to impact

Range: impact energy of up to 20 J

PN-EN 60079-31:2014-10 IEC 60079-31:2013 Ability of the enclosure to withstand

pressure

Range: up to 3 MPa

PN-EN 60079-31:2014-10 IEC 60079-31:2013

Thermal tests, temperatures and temperature rise

Range: up to +450°C

PN-EN 60079-31:2014-10 IEC 60079-31:2013 Solid planar materials used to

avoid electrostatic charge accumulation

Surface resistance of non-metallic materials

Range: up to R = 1 x 1012 Ω

PN-EN 60079-32-2:2015-08

Resistance between non-metallic materials points

PN-EN 60079-32-2:2015-08

Volume resistance of non-metallic materials

PN-EN 60079-32-2:2015-08

Machines and equipment.

Degrees of protection provided by

enclosures (IP code)

Range of IP 1X, 2X, 3X, 4X, 5X, 6X, X4, X5, X6, X7, X8, X9

PN-EN 60529:2003+A2:2014-07 PN-G-50003:2003

PN-EN IEC 60034-5:2021-01 Machines and equipment.

Degrees of protection provided by enclosures (IK code)

Range of IK 01, 02, 03, 04, 05, 06, 07, 08, 09, 10

Method: Test Ehc Vertical hammer

PN-EN 62262:2003

PN-EN 60068-2-75:2015-01

Non-electrical equipment for use in potentially explosive

atmospheres

Method: direct PN-EN ISO 80079-36:2016-07

wg Załącznika ZC Resistance to impact

Range: impact energy of up to 20 J Resistance to drop-test impact Maximum surface temperature Range: up to +450°C

Non-electrical type of protection constructional safety ''c'', control of ignition sources ''b'', liquid immersion ''k''

Pressure resistance of the housing Range: up to 3 MPa

Method: static pressure load

PN-EN ISO 80079-37:2016-07 wg Załącznika ZB

Wersja strony: A

(5)

Standards and/or documented testing procedures Solid planar materials used to

avoid electrostatic charge accumulation

Surface resistance of non-metallic materials

PN-EN 61340-2-3:2016-11

Resistance between non-metallic materials points

PN-EN 61340-2-3:2016-11

Volume resistance of non-metallic materials

PN-EN 61340-2-3:2016-11 Surface resistance of non-metallic

housing parts

PN-EN IEC 60079-0:2018-09 Surface resistance PN-EN ISO 80079-36:2016-07 Non-electrical equipment for

explosive atmospheres

Breakdown voltage PN-EN ISO 80079-36:2016-07

Electrical machines and mining equipment

Creepage distances and clearances Direct measurement

PN-G-50003:2003 Insulation resistance

Range: up to 1TΩ (at U = 5 kV)

PN-G-50003:2003 Insulation electrical strength

PN-G-50003:2003

The equipment and insulation thermal endurance to humid constant heat Range: up to 95°C and up to 98% RH Method: Cab test

PN-G-50003:2003

Thermal endurance to cold Range: down to -75°C

PN-G-50003:2003 Thermal endurance to dry heat

Range: up to 180°C PN-G-50003:2003

Heating, temperatures and temperature

Rise, Range: up to +450°C

PN-G-50003:2003

Cable and conductor glands PN-G-50003:2003

PN-EN IEC 60079-0:2018-09 Machines and equipment

(including electrical) Thermal resistance to cold Range: down to -75°C Method: Test A

PN-EN 60068-2-1:2009

Resistance to dry heat Range: up to + 160 ° C Method: Test Bb; Trial of Bd;

Attempt at Be

PN-EN 60068-2-2:2009

Test Db: Damp cyclic heat (12h + 12h

cycle) PN-EN 60068-2-30:2008

Thermal resistance to humid constant Heat, Range: up to 95°C and to 98%

RH

Method: Cab test

PN-EN 60068-2-78:2013-11

Wersja strony: A

(6)

Standards and/or documented testing procedures Electrical appliances for

household and similar

- Checking marking

- Check the power and current - Check heating

- Check the leakage current and electric strength at operating temperature - Test for moisture

- Check the leakage current and electric strength

- Check the overload protection of the transformer and circuits fed from the transformer

- Check the operation under abnormal conditions

- Check the internal wiring

- Checking the grounding connection - Check the screws and connections - Check the insulation distances of air and

surface and the thickness of solid insulation

- Check the start-up of equipment with motorized

- Check the wear resistance - Check the stability and mechanical hazard

- Verification of components,

Checking the connection to the power supply and external hoses

- Check the external wiring terminal

PN-EN 60335-1:2012 +A11:2014-10+A13:2017-11 +A1:2019-10+A2:2019-11 +A14:2020-05

Vacuum cleaners and water- suction cleaning appliances

PN-EN 60335-2-2:2010 +A1:2013-05+A11:2013-05

Electric irons PN-EN 60335-2-3:2016-03

Stationary cooking ranges, hobs,

ovens and similar appliances PN-EN 60335-2-6:2015-05

+A1:2020-07+A11:2020-09 Shavers, hair clippers and

similar appliances

PN-EN 60335-2-8:2015-12 +A1:2016-04

Grills, toasters and similar portable cooking appliances

PN-EN 60335-2-9:2007+A12:2008 +A13:2011

Floor treatment machines and

wet scrubbing machines PN-EN 60335-2-10:2004+A1:2008

Warming plates and similar

appliances PN-EN 60335-2-

12:2004+A1:2008+A2:2019- 11+A11:2019-11

Deep fat fryers, frying pans and

similar appliances PN-EN 60335-2-

13:2010+A11:2012+A1:2019-11

Kitchen machines PN-EN 60335-2-14:2009+A1:2009

+A11:2012+A12:2016-03

Appliances for heating liquids PN-EN 60335-2-15:2016-04/

+A11:2018-10

Food waste disposers PN-EN 60335-2-16:2004+A1:2008

+A2:2012+A11:2018-09 Blankets, pads, clothing and

similar flexible heating appliances

PN-EN 60335-2-17:2013-06 +A11:2019-11+A1:2020-09

Storage water heaters PN-EN 60335-2-21:2006+A2:2009

Appliances for skin or hair care PN-EN 60335-2-23:2006+A1:2008

+A11:2010+A2:2015-03 Refrigerating appliances, ice-

cream appliances and ice makers PN-EN 60335-2-24:2010 +A1:2019-

01+A2:2019-02+A11:2020-11

Microwave ovens, including combination microwave ovens

PN-EN 60335-2-25:2012 +A1:2015-11+A2:2016-04

Sewing machines PN-EN 60335-2-28:2004+A1:2008

+A11:2018-10

Battery chargers PN-EN 60335-2-29:2005+A2:2010

+A11:2018-11

Room heaters PN-EN 60335-2-30:2010

+A11:2012+A1:2020-09 +A12:2021- 02

Range hoods and other cooking

fume extractors PN-EN 60335-2-31:2015-02

(7)

Edition no 12,15.07.2021 7/22 Particular requirements for

massage appliances

- Checking marking

- Check the power and current - Check heating

- Check the leakage current and electric

strength at operating temperature - Test for moisture

- Check the leakage current and electric

strength

- Check the overload protection of the transformer and circuits fed from the transformer

- Check the operation under abnormal conditions

- Check the internal wiring

- Checking the grounding connection - Check the screws and connections - Check the insulation distances of air and

surface and the thickness of solid insulation

- Check the start-up of equipment with motorized

- Check the wear resistance - Check the stability and mechanical hazard

- Verification of components,

Checking the connection to the power supply and external hoses

- Check the external wiring terminal

PN-EN 60335-2-32:2009 +A2:2015-03

Particular requirements for

instantaneous water heaters PN-EN 60335-2-35:2016-

03+A1:2020-05 Particular requirements for

commercial electric doughnut fryers and deep fat fryers

PN-EN 60335-2-37:2009+

A11:2012+A12:2016-05

Particular requirements for electrical heat pumps, air- conditioners and dehumidifiers

PN-EN 60335-2-40:2004+A11:2005 +A12:2005+A1:2006+A2:2009 +A13:2012

Particular clothes dryers and towel rails

PN-EN 60335-2-43:2005+A1:2006 +A2:2009

Portable heating tools and similar appliances

PN-EN 60335-2-45:2007+A1:2008 +A2:2012

Commercial electric appliances for

keeping food and crockery warm PN-EN 60335-2-

49:2010+A11:2012+A2:2020-05

Oral hygiene appliances PN-EN 60335-2-52:2004+A1:2008

+A11:2010+A12:2020-04 Particular requirements for sauna

heating appliances and infrared cabins

PN-EN 60335-2-53:2012

Surface-cleaning appliances for household use employing liquids or steam

PN-EN 60335-2-54:2009 +A11:2013-05+A1:2015-11

Projectors and similar appliances PN-EN 60335-2-56:2003+A1:2008

+A2:2014-12 Particular requirements for insect

killers PN-EN 60335-2-59:2007+A2:2010

+A11:2018-12

Thermal storage room heaters PN-EN 60335-2-61:2008+A2:2009

Water-bed heaters PN-EN 60335-2-66:2003+A1:2008

+A2:2012+A11:2020-01

Portable immersion heaters PN-EN 60335-2-74:2008+A2:2010

+A11:2018-11 Commercial dispensing appliances

and vending machines

PN-EN 60335-2-75:2005+A1:2005 +A11:2006+A2:2009+A12:2010

Outdoor barbecues PN-EN 60335-2-78:2004

+A1:2008+A11:2020-07

Fans PN-EN 60335-2-80:2007+A2:2009

Foot warmers and heating mats PN-EN 60335-2-81:2003+A1:2007

+A2:2012

(8)

Edition no 12,15.07.2021 8/22 Amusement machines and

personal service machines

PN-EN 60335-2-82:2004 +A1:2008+A2:2020-07

Humidifiers intended for use with heating, ventilation, or air- conditioning systems

PN-EN 60335-2-88:2003

Commercial refrigerating

appliances and ice-makers with an incorporated or remote refrigerant unit or motor-compressor

PN-EN 60335-2-89:2012 +A1:2016- 04+A2:2018-04

Flexible sheet heating elements for

room heating PN-EN 60335-2-96:2005+A2:2009

Drives for shutters, awnings,

blinds and similar equipment PN-EN 60335-2-97:2007+A11:2008

+A2:2010+A12:2015-02

Humidifiers PN-EN 60335-2-

98:2009+A2:2009+A11:2020-01 Gas, oil and solid-fuel burning

appliances having electrical connections

PN-EN-60335-2-102:2016-03

(9)

Standards and/or documented testing procedures Heating boilers for solid fuels,

manually and automatically stoked, nominal heat output of up to 500 kW

- Determination of the consumption of auxiliary electricity;

- Determination of the temperature of the outer surface;

- Testing the operation of the temperature regulator and the safety temperature limiter of the heating boiler

PN-EN 303-5:2012

Luminaires - Strength marking

- Mechanical and electrical construction with the exception of: requirements for vibration and UV radiation

- The correctness of external and internal

wiring

- Adapting to the ground

- Protection against electric shock - Resistance to dust, solids and water - Insulation resistance and electric strength, current, protective conductor current

- Clearances surface and air

- Hardness test and attempt Thermal - Resistance to heat, fire and to stray currents

- The correctness of the construction screw terminals

- The correctness of the construction of terminals screwless electrical

connectors

PN-EN 60598-1:2015-04 +A1:2018- 04

PN-IEC 598-2-1:1994+Ap1:2000 EN 60598-2-1:1989

PN-EN 60598-2-4:2018-06 PN-EN 60598-2-5:2016-02 PN-EN 60598-2-24:2014-02 PN-EN 60598-2-2:2012

Low-voltage switchgear and

controlgear assemblies - Verification of marking - Test for raising

- Check the degree of protection (IP code)

- Check the insulation distances of air and surface

- Check the effectiveness of the protective circuit

- Verification of dielectric properties - Check the temperature rise - Checking the insulation resistance - Electrical strength test of insulation - Verification of protection against residual voltages

PN-EN 61439-1:2011 PN-EN 61439-2:2011 PN-EN 61439-3:2012 PN-EN 61439-4:2013-06 PN-EN 61439-5:2015-02 PN-EN 62208:2011 Safety of machinery - Electrical

equipment of machines PN-EN 60204-1:2018-12

(10)

Edition no 12,15.07.2021 10/22 Hand - held motor - operated

electric tools

- Marking check

- Verification of protection against access to live parts

- Boot check

- Check power consumption and current

- Heating check

- Leakage current check - Moisture resistance check - Checking the electrical strength - Checking the protection against overload of the transformer and the circuits supplied from the transformer - Checking long-term work

- Checking the operation of the device in abnormal conditions

- Checking the protection against mechanical damage

- Checking the structure - Check the internal wiring - Checking the component parts - Checking the connection to the power supply and flexible connection cables

- Checking the external wiring - Checking the earthing connection - Checking screws and connections - Checking surface and air insulation gaps and the thickness of solid insulation

- Durability check - Rust resistance test - Checking resistance to high temperature and fire

PN-EN 60745-1:2009+A11:2011 PN-EN 62841-1:2015-11

Drills and impact drills PN-EN 60745-2-1:2010

PN-EN 62841-2-1:2018- 03+A11:2020-03 Screwdrivers and impact

wrenches

PN-EN 60745-2-2:2010 PN-EN 62841-2-2:2015-03

Grinders, polishers and disk-type sanders

PN-EN 60745-2-3:2011 +A2:2014-01+A11:2015-01+

A12:2015-08+A13:2016-03 Sanders and polishers other than

disk type PN-EN 60745-2-4:2010+A11:2012

PN-EN 62841-2-4:2015-02

Circular saws PN-EN 60745-2-5:2011

PN-EN 62841-2-5:2015-02

Hammers PN-EN 60745-2-6:2010

Shears and nibblers PN-EN 60745-2-8:2009

PN-EN 62841-2-8:2017-01

Tappers PN-EN 60745-2-9:2009

PN-EN 62841-2-9:2015-07 Reciprocating saws (jig and

sabre saws)

PN-EN 60745-2-11:2010 PN-EN 62841-2-11:2016-08 +A1:2020-10

Concrete vibrators PN-EN 60745-2-12:2009

Chain saws PN-EN 60745-2-13:2009+A1:2011

PN-EN 62841-4-1:2020-08 z wyłączeniem pkt.19.107

Planers PN-EN 60745-2-14:2009+A2:2010

PN-EN 62841-2-14:2016-02

Hedge trimmers PN-EN 60745-2-15:2009+A1:2010

PN-EN 62841-4-2:2019-10

Tackers PN-EN 60745-2-16:2011

Routers and trimmers PN-EN 60745-2-17:2010

PN-EN 62841-2-17:2018-02

Strapping tools PN-EN 60745-2-18:2009

Jointers PN-EN 60745-2-19:2009+A1:2010

Band saws PN-EN 60745-2-20:2009

Drain cleaners PN-EN 60745-2-21:2009+A1:2011

PN-EN 62841-2-21:2019-08

Cut-off machines PN-EN 60745-2-22:2011

+A11:2013-10 Die grinders and small rotary

tools PN-EN 60745-2-23:2013-10

(11)

Standards and/or documented testing procedures Safety requirements for electrical

equipment for measurement, control, and laboratory use

- Marking and documentation - Protection against electric shock - Protection against mechanical hazards

- Device temperature limits and heat resistance

- Protection against the dangers of liquids

- Protection with locks

PN-EN 61010-1:2011+A1:2019-04

Medical electrical equipment Marking durability Legibility of the marking Voltage and stored charge measurement

Protective connection impedance Leakage Current:

- earth leakage current - touch leakage current - patient leakage current - patient auxiliary current - patient's total leakage current Insulating gaps Electrical strength of the insulation

Air and surface gaps

Heat resistance Range: up to 180 ° C Moisture initial stabilization Humidity range in climate mode up to 98%

Protection against mechanical hazards with the exception of point 9.5 and 9.6

Temperature during normal use Temperature of the applied parts Degree of protection against:

- overflow in a medical device, - dousing on a medical device, - ingress of water or solids into the medical device

Damage conditions excluding points 13.2.11

Construction, mechanical strength

PN-EN 60601-1:2011 +A1:2014-02+A12:2014-12

Safety of primary and secondary lithium cells and batteries during transport

- Checking the height simulation, - Thermal study, -

short circuit test, - Crushing test, - Forced discharge test - Fall test (packaging test)

UN TEST

Nr ST/SG/AC.10/11/Rev.7:2019 Test T1, T2, T5, T6, T8

IEC 62281:2019

Test T-1, T-2, T-5, T-6, T-8, P-1

(12)

Edition no 12,15.07.2021 12/22 Laboratory of Mechanical and Physical Research

Aronii 4 street, 44-102 Gliwice Poland Tested objects/Group of objects Tested features and test/

measurement methods Standards and/or documented testing procedures Plastics - Determination of

flexural properties Flexural strength

Load range: up to 1000 kN Bending test PN-EN ISO 178:2011+A1:2013-06 PN-EN ISO 178:2019-06

Compressive strength Load range: up to 1000 kN Bending test

PN-C-89071:1993

Methods of testing cement Determination of strength

Flexural strength Compressive strength Load range: up to 1000 kN Bending test

Compression test

PN-EN 196-1:2016-07

Rubber and plastic hoses and

hose assemblies Geometric linear dimensions Range: up to 150 mm Method: direct

PN-EN ISO 4671:2008+A1:2011

Resistance to test pressure Range: up to 2500 bar Method: static pressurization

PN-EN ISO 1402:2010

Resistance to bursting pressure Range: up to 2500 bar

PN-EN ISO 1402:2010

Leakage

Range: up to 2500 bar Method: static pressurization

PN-EN ISO 1402:2010

Test with hydraulic pulsating pressure

without bending PN-EN ISO 6803:2017-04

Resistance to sheath abrasion

Range: 5 to 51 mm PN-EN ISO 6945:2002

PN-EN 853:2015-05 PN-EN 856:2015-05 PN-EN 856+AC:2019-04 PN-EN 854:2015-05 PN-EN 857:2015-05 PN-G-32010:2012 Method: flammability test PN-EN ISO 8030:2014-09 Surface resistance PN-EN ISO 8031:2021-01 Mining hydraulic drives and

control systems

Minimum destructive pressure Range: up to 2500 bar Method: static pressurization Geometric linear dimensions Range: up to 150 mm Method: direct

PN-G-32000:2011 DIN 20043:2003

Plastics and other non-metallic

materials Flammability – exposition time 10s PN-EN ISO 340:2013-07 p.5.7 except p.5.7.5 i p.5.7.6

Flammability PN-EN ISO 9773:2003+A1:2005

Flammability – method B PN-EN 60695-11-10:2014-02

Glow wire test PN-EN 60695-2-10:2013-02

PN-EN 60695-2-11:2015-02 Attempting to press in the ball PN-EN 60695-10-2:2014-10 Mining workings lining soldered

meshes Condition of surface

Visual method PN-G-15050:2018-01

Geometric dimensions Range: up to 2000 mm Mesh bending strength Load range: up to 1000 kN Rod material strength Load range: up to 1000 kN Soldered joint shear strength Load range: up to 1000 kN

(13)

Standards and/or documented testing procedures Roadway support base Dimensions and forms PN-G-15023:2019-03

Base resistance to piercing Funkcjonalność

Load range: up to 1000 kN Steel double-action props of

roadway supports

Dimensions PN-G-15024:2017-10

Transverse stability

Stability perpendicular to the prop axis Longitudinal stability

Load range: up to 100 kN Impact attenuating playground

surfaces Critical fall height

Range: height (0 to 3.7) m (HIC coefficient)

PN-EN 1177+AC:2019-04

Playground equipment and surfacing - Part 1: General safety requirements and test methods

Structural strength Method: strength test of structural elements

PN-EN 1176-1:2017-12 Accessible for adults Measurement of

geometric quantities Range: (0 - 3000) mm

PN-EN 1176-1:2017-12

Fall protection

Measurement of geometric quantities Range: (0 - 3000) mm

PN-EN 1176-1:2017-12

Finishing the device

PN-EN 1176-1:2017-12

Moving parts

PN-EN 1176-1:2017-12

Protection against jamming Testing with samplers,

Measurement of geometric quantities Range:(0 - 3000) mm (0 - 220) ˚

PN-EN 1176-1:2017-12

Protection against injuries during movement and falling

Measurement of geometric quantities calculations

Range: (0 - 20,000) mm

PN-EN 1176-1:2017-12

Means of access

Measurement of geometric quantities Range: (0 - 3000) mm (0 - 220) ˚

PN-EN 1176-1:2017-12

Connections

Method: sensory method PN-EN 1176-1:2017-12 Wear parts

Method: sensory method PN-EN 1176-1:2017-12 Ropes

PN-EN 1176-1:2017-12

Chains:

PN-EN 1176-1:2017-12

Hanging heavy beams Testing with samplers,

Measurement of geometric quantities force measurement

Range: (0 - 3000) mm (0 - 1000) N.

PN-EN 1176-1:2017-12

Marking

Method: sensory method

PN-EN 1176-1:2017-12

(14)

Standards and/or documented testing procedures Playground equipment and

surfacing - Part 2: Additional specific safety requirements and test methods for swings

Geometric dimensions

Range: (0 - 20,000) mm

PN-EN 1176-2+AC:2020-01

Means of suspension

PN-EN 1176-2+AC:2020-01

Fall height and impact surface Measurement of geometric quantities calculations

Range: (0 - 3000) mm (0 - 220) ˚

PN-EN 1176-2+AC:2020-01

Marking Method: sensory method Geometric dimensions

PN-EN 1176-2+AC:2020-01

Playground equipment and surfacing - Part 3: Additional specific safety requirements and test methods for slides

Marking Method: sensory method Geometric dimensions

PN-EN 1176-3:2017-12

The surface of the slide Method: test with samplers

PN-EN 1176-3:2017-12

Free space

PN-EN 1176-3:2017-12

Free space

PN-EN 1176-3:2017-12

Marking Method: sensory method PN-EN 1176-3:2017-12

Wersja strony: A

(15)

surfacing - Part 4: Additional specific safety requirements and test methods for cableways

The design and mounting knots of the carrier rope

PN-EN 1176-4+AC:2019-03

Thrust bumpers

Measurement of geometric quantities Range: (0 - 220) ˚

PN-EN 1176-4+AC:2019-03

Crane

Method: sensory method PN-EN 1176-4+AC:2019-03 Suspension assembly

PN-EN 1176-4+AC:2019-03

Cable cars arranged in parallel Measurement of geometric quantities Range: (0 - 3000) mm

PN-EN 1176-4+AC:2019-03

Handles

Testing with samplers

PN-EN 1176-4+AC:2019-03

Speed

Measurement of time and geometrical quantities, calculations

Range: (0 - 20,000) mm

PN-EN 1176-4+AC:2019-03

Free fall height

PN-EN 1176-4+AC:2019-03

Ground clearance Measurement of force and geometrical quantities

Range: (0 - 1000) N (0 - 3000) mm

PN-EN 1176-4+AC:2019-03

Support rope height

Measurement of geometric quantities Range: (0 - 20,000) mm

PN-EN 1176-4+AC:2019-03

Fall area and impact surface

PN-EN 1176-4+AC:2019-03

Marking

Method: sensory method PN-EN 1176-4+AC:2019-03

Wersja strony: A

(16)

surfacing - Part 6: Additional specific safety requirements and test methods for rocking

equipment

Free fall height

PN-EN 1176-6+AC:2019-03

Tilting the seat / standing position Measurement of force and geometrical quantities Range:

(0 - 1000) N (0 - 3000) mm (0 - 220) ˚

PN-EN 1176-6+AC:2019-03

Jamming, crushing

Testing with samplers PN-EN 1176-6+AC:2019-03 Traffic braking

PN-EN 1176-6+AC:2019-03

Footrests

PN-EN 1176-6+AC:2019-03

Hand rests

PN-EN 1176-6+AC:2019-03

Side view profiles Testing with samplers

PN-EN 1176-6+AC:2019-03

Deadlock

PN-EN 1176-6+AC:2019-03

Fall space

PN-EN 1176-6+AC:2019-03

Lateral deflection (type 1) Measurement of force and geometrical quantities

Range: (0 - 1000) N (0 - 3000) mm

PN-EN 1176-6+AC:2019-03

Rotation around the vertical axis (type 3A)

Measurement of force and geometrical quantities Range: (0 - 1000) N (0 - 3000) mm (0 - 220) ˚

PN-EN 1176-6+AC:2019-03

Total Movement Range (Type 4)

PN-EN 1176-6+AC:2019-03

Free fall height (type 6)

PN-EN 1176-6+AC:2019-03

Marking

Method: sensory method PN-EN 1176-6+AC:2019-03

(17)

surfacing - Part 11: Additional specific safety requirements and test methods for spatial network

Fall space

PN-EN 1176-11:2014-11

Mesh sizes in three-dimensional flat nets

Range: (0 - 3000) mm

PN-EN 1176-11:2014-11

Protection against injuries in the fall area

Range: (0 - 3000) mm

PN-EN 1176-11:2014-11

Convergent elements Testing with testers, force measurement

Range: (0 - 3000) mm (0 - 1000) N.

PN-EN 1176-11:2014-11

Permanently installed outdoor fitness equipment - Safety requirements and test methods

Structural strength

Method: strength test of structural elements

PN-EN 16630:2015-06 PN-EN 1176-1:2017-12 Finishing the device

PN-EN 16630:2015-06

Surfaces that can be walked on Measurement of geometric quantities Range: (0 - 3000) mm

PN-EN 16630:2015-06

Moving parts

PN-EN 16630:2015-06

Protection against jamming Testing with samplers

PN-EN 16630:2015-06

Loads and resistors

Method: sensory method PN-EN 16630:2015-06 Regulating and blocking mechanisms

PN-EN 16630:2015-06 Accessibility of entry / exit

PN-EN 16630:2015-06 Connections

PN-EN 16630:2015-06 Wear parts

Method: sensory method PN-EN 16630:2015-06 Grip / grip

PN-EN 16630:2015-06

Ropes Measurement of geometric quantities

Range: (0 - 3000) mm

PN-EN 16630:2015-06

Chains

PN-EN 16630:2015-06 Surfaces and spaces

PN-EN 16630:2015-06

Free fall height

PN-EN 16630:2015-06

Marking Method: sensory method PN-EN 16630:2015-06

Wersja strony: A

(18)

Standards and/or documented testing procedures Sports and recreational equipment

- Parkour equipment - Safety requirements and test methods

Structural strength

Method: strength test of structural elements

PN-EN 16899:2017-02

Childproof accessibility

Measurement of geometric quantities Calculations

Range: (0 - 3000) mm

PN-EN 16899:2017-02

Finishing the device Testing with samplers

PN-EN 16899:2017-02

Parkour beams and rails

Measurement of geometric quantities Range: (0 - 3000) mm (0 - 220)˚

PN-EN 16899:2017-02

Closed passages

PN-EN 16899:2017-02

Protection against injuries during movement and falling

PN-EN 16899:2017-02

Spacing

PN-EN 16899:2017-02

Protection against jamming Testing with samplers

PN-EN 16899:2017-02

Free fall height

PN-EN 16899:2017-02

Marking

PN-EN 16899:2017-02

(19)

Standards and/or documented testing procedures Stationary training equipment —

Part 1: General safety

requirements and test methods

Stability

Functional tests at an inclination of 10˚

PN-EN ISO 20957-1:2014-02 Outdoor construction

Testing with probes, visual inspection, tactile tests

User imprisonment

Visual inspection and functional tests Regulation and lock mechanisms Functional tests, visual inspections Strength of ropes, belts, chains and slings

Tensile strength test Rope and belt guides Functional tests Flywheels

Testing with samplers Handles

Functional tests, secure mounting Weighting equipment

Force measurement

Heart rate measuring system Function check

Internal and external load Load test

Marking Inspection Stationary training equipment —

Part 4: Strength training benches, additional specific safety

requirements and test methods

Geometric dimensions Linear measurement

PN-EN ISO 20957-4:2017-03 Inspection

Functional tests

Rotary stability of the barbell

Rotary and longitudinal stability of the bench

Stationary training equipment — Part 5: Stationary exercise bicycles and upper body crank training equipment, additional specific safety requirements and test methods

Geometric dimensions PN-EN ISO 20957-5:2017-03 Inspection

Tactile tests Functional tests Temperature rise

Gear components and rotating components

Testing with samplers Internal load

Load test Seat tilt Load test Stability

Stationary training equipment — Part 9: Elliptical trainers, additional specific safety requirements and test methods

Geometric dimensions PN-EN ISO 20957-9:2017- 03+A1:2019-07

Inspection Functional tests

Squeezing and crushing places Testing with samplers

Temperature rise Internal load Load test Stability

Wersja strony: A

(20)

Edition no 12,15.07.2021 20/22 Noise Tests Laboratory

Tested objects/Group of objects Tested features and test/

measurement methods Standards and/or documented testing procedures Work environment - noise Acoustic pressure level

Range: from 23 to 137 dB Reference method

PN-EN ISO 11202:2012

Acoustic power level

Acoustic energy level (calculated) Machines and equipment - noise Equivalent noise level A

Range: (23 to 137) dB Method: direct measurement

PN-EN ISO 3746:2011+Ap1:2017- 09

Acoustic power level

Acoustic energy level (calculated) Work environment – Human

exposure to mechanical vibrations

Whole-body vibration

Effective frequency-weighted vibration acceleration

Range: (0.003 – 700) m/s2

Measurement method: direct

PN-EN 14253+A1:2011

Daily exposure expressed by energetically equivalent 8-hour exposure

to the effective frequency-weighted vibration acceleration, dominating among

the vibration accelerations, determined for

three directional components, taking into

account adequate coefficients (1.4awx, 1.4awy, awz).

30-minute and shorter exposure expressed by the effective frequencyweighted vibration acceleration,

dominating among the vibration accelerations, determined for three directional components, taking into account adequate coefficients (1.4awx, 1.4awy, awz) (obtained by

calculations).

Wersja strony: A

(21)

Standards and/or documented testing procedures Work environment – Human

exposure to hand-transmitted mechanical vibrations

Effective frequency-weighted vibration acceleration

Range: (0.01 – 700) m/s2

Measurement method: direct

PN-EN ISO 5349-2:2004

Daily exposure expressed by energetically equivalent 8-hour exposure

to the vector sum of effective frequencyweighted

vibration accelerations

determined for three directional components (a^hwx, a^hwy, a^hwz).

30-minute and shorter exposure expressed by the vector sum of effective

frequency-weighted vibration accelerations determined for three directional components (ahwx, ahwy,

ahwz)

(obtained by calculations).

Wersja strony: A

(22)

Edition no 12,15.07.2021 22/22

HOLOGRA MHOLOG RAM HOLOGRA

MHOLOG

List of changes

Scope of Accreditation No.AB 1340

Change status: original version - A