• Nie Znaleziono Wyników

Installing the Converter 3-9

N/A
N/A
Info
Pobierz
Protected

Academic year: 2021

Share "Installing the Converter 3-9 "

Copied!
1
0
0

Ładowanie.... (Zobacz pełny tekst teraz)

Pobierz teraz ( 1 Stron )

Pełen tekst

(1)

Installing the Converter 3-9

590+ Series DC Digital Converter

Connection Diagrams

EMERGENCY STOP RELAY

AUXILIARY SUPPLY SIGNAL 0V SPEED SETPOINT No. 1 CURRENT DEMAND TOTAL SETPOINT ZERO SPEED DRIVE HEALTHYDRIVE READY SETPOINT RAMP

C1C2

F1C9G2 A+ 10K

START/ ENABLE B9A1B8C5C3 B3A4B4A8A3A2A6B5B6B7TH2TH1

C9C1N G1L43 L1L2 F-F+ PEA-

L3PE FIELD OUTPUT

+

THERMISTOR

S S S

RL RL RL ARMATURE

M

PE

* *

PROTECTIVE EARTH Filter Start ContactorCON

3-PHASE SUPPLY 110V - 690VAC Branch Protection Fuses star-point earth near drive

AC Line Choke SPEED SETPOINT No. 2/

+

3-PHASE CONTACTOR

3 PH 50/60Hz 110/240VAC 1 PH 50/60Hz MICROTACHAC TACHO

select feedback type from MMI ENCODER (isolated)

EXTERNAL TRIP

FL1FL2

EXTERNAL AC FIELD 500VAC MAX 1 PH 50/60Hz DC

PROGRAM STOP COAST STOP MOTORINPUT

RUN DC TACHO G4G3

+ E1-6

*

use internal field connection for EMC compliance ## # Links required if Thermistor and/or External Trip switch not fitted

(optional) H1-6 RS485 LINK TECHNOLOGY BOX

EXTERNAL MOTOR

(D7)(D8)(D6)(D5)(D1)(D2) (D4)(D3)THERM-THERM+

High Speed Fuses

Figure 3-8 Power Connections: Frames 1, 2, 3 & 4 (`general purpose’ configuration)

FRAMES 1, 2, 3 & 4 Bold lines indicate

"minimum connections"

Cytaty

Pobierz teraz ( PDF - 1 Stron - 97.48 KB )

Powiązane dokumenty

Where is the plot of “Speed” set? 3

Which famous sportsperson appears in “The Hangover”?. What is the name of the hospital where Dr Gregory

nr 9/3

Święto nie tylko jest upamiętnieniem ważnego dla historii Romów wydarzenia, ale również zwraca uwagę na podstawo- we problemy z  jakimi stykają się Romowie rozproszeni po

1 9 ^ 3

kładu” w jego początkach (1569— 1599) rozświetlić przede wszystkim w oparciu o źródła Rzymskiego A rchiw um Towarzystwa Jezusowego d o ­ tychczas nie

VARIABLE SPEED DRIVE

Communications port RS485 and Modbus RTU protocol (as accesory) Operation features PID control, 3-wire, up-down operation. Standards CE,

Variable Speed Drive

The protection will be enabled if the current is below the value adjusted in this parameter when the operating frequency is twice the motor rated slip speed.. The protection will be

Variable Speed Drive

F61 NO INPUT V This fault will be shown in the display of the SD700 when the start command is activated and the input voltage applied to the drive is lost, and the drive is powered

variable speed drive

Drive will trip (it turns off the output to the motor) because of fault ‘F13 HI V IN’ when average voltage, measured at the input of the equipment, is higher than the value set

Variable Speed Drive

Although the control board is insulated galvanically, for safety reasons it is recommended not to modify the wiring while the equipment is connected to the input power