\Pioauaii, Una.
20 STERN AVE.
SPRINGFIELD, NEW JERSEY 07081 U S A 2N1600
SILICON PNPN CONTROLLED RECTIFIER
TELEPHONE: (973) 376-2922 (212) 227-6005 FAX: (973) 376-8960
maximum ratings — all temperatures Indicated are stud temperatures 3NIMO Unit VFI,,,I) Forward Voltage in the "off" Condition at 125'C (Note 1) 50 volts V, Peak Inverse Voltage -65'C to + 150*C 50 volts I, Average Rectified Forward Current at 80*C 3 A lf Average Rectified Forward Current at 125*C 1 A i, Recurrent Peak Forward Current at 80*C 10 A i, Recurrent Peak Forward Current at 125°C 3 A if|iu>g.| Surge Current. 1 Cycle at 60 cps at 80°C 25 A ls Forward Gale Current at 125"C 100 ma V6» Cater Peak Inverse Voltage-65'C t o + 150°C S volts Tj Operating Temperature Range *C TII, Storage Temperature Range *C TJ Junction Temperature *C Altitude at Maximum Ratings ft.
Stud Torque in.-lbs.
specifications — all temperatures indicated are stud temperatures
BVf Min Forward Breakover Voltage at 125"C (Note 1) BV» Min Reverse Breakdown Voltage at 25°C (Note 2) I, Max dc Reverie Current at Rated V, at 25*C U Max dc Reverse Current at Rated V, at 125° C lF|0if) Max dc Forward Current or Vfi.ii) at 25°C lr.,,11, Max de Forward Current at Vr.(1,if| at 125*C VF Max Forward Voltage Drop at IF = 3Adc at 25'C IST Max Gate Current to Trigger of 25'C (Note 3) VGI Min Gale Voltage to Trigger at 125'C (Note 3) IH Max Holding Current at 25°C
BVe Min Gate Breakdown Voltage at 25°C (Note 2) Vs Max Fwd. Gate Voltage Drop at Ig = 25 ma at 25*C
NOTESi
1. M*oiur«d with a 1000 ohm •xttrnal ihurit>r*»li'cm»
bwlwun thoj gal, and cathod*.
2. Breakdown voltage it lh« volfag* at which the current Ii 10 ma.
2N1600 Un!l
60 volts 60 valh '0.25 ma
] ma 0.25 ma 1 ma
volti ma 0.25 void
25 ma 6 volt) 3 volts 2 10
OUTLINE DRAWING
(Complies with JEDEC registered TO-64 outline) J
-,_ a r-TERM.2 0T-1 I ((CATHODE)
—|-±±ir-7"-
00
TERM.
(GATE)
— N, i—TERM
|3(ANQDE)
SEATING PLANE
NOTES:
(1) Contour and orlentillon of fixed larmlnjl lugs art optional.
(2) Thi oulllni contour {olth ncepllon ol hauion) la opllonal wllkln <oni dcflntd br «>0 and J.
(3) Minimum rfUmtltr of Itallnf planf.
(4) A chintw (or undlreut) on ont or bolh indi of htufon*! portion It optloiul, (5) Minimum dlflirfnca In lernlnal Knulhi lo
eitabllsb datum Ifna for numbering lermlnala.
(E) Pilch diameter—thread 10-12 NF.JA (Coaled).
Relerencl (Scr«r Thread Standardi lor Federal Senlcea 1937) Himfbiok 1957 H2*.
(7) MlnlmiiM toaclrtit between terminals.
(n) Iniulatlnf kit available upon request.
CD IO-3Z STEEL NUT CADMIUM PLATCD
®LOCKWHSHCn,
CADMIUM PLATCD
STEEL A
B
*0*0i c
t BI f 1
,,M N N,
^W*I IN JOO .OAQ
.400 .424 .013 .060 060 .700 .IS]
.400 040 J6SH
CHIS
.400 .136 a_.4j!4
,«7
.175 .S55"
189 .451
07*
.075 .lfi<17
MILL
7,62 2.0]
10.16 10.77 .330 l.?>7 1.52
i;.ja
4.14 10.16
i.o;
^l.7U'
Minus
10.11 3.4!
10.77
ll.lj
4.45 I~TT72
^.la n.il Lit
l.ffl1.91
..,• ..' tine i
2 }.'
7 5 4 2
f.
NJ Semi-Conductors reserves the right to change test conditions, parameters limits and package dimensions without
notice information famished by NJ Semi-Conductors is believed to be both accurate and reliable at the time of going to
press. However NJ Semi-Conductors assumes no responsibility for any errors or omissions discovered in its use. N I
Semi-Conductors encourages customers to verify that datasheets are current before placing orders.
DIMENSIONAL OUTLINE %"
SELl.tVII.LE WiSMH 5 0 0 0 0 Mil ( 2SS I O MIN t
- -J1UNF-I1 trt'O NUT
-MUNf SITH'O - /
j fl«T *ASHCR |j| 0 D , MIL JT'O IS7W-OIO
- S T E P WASHER »00( 0 0 -??J , f L«NO£ 0 D-554 ,-J4j I 0
10HOUE KgumCMLNIIINON LUBHIC«I[D IH'UI ' 10 INCH -Lit MW
I9lttCN-l.il MA»
IHl COtlECrOK I9EIEC1HIOLLT CONWCIED 10 IME C»tl
OO?
•004
