TRYB STRONY
Figure 29. SEQUENCE MODE SETTING PAGE
Figure 29. SEQUENCE MODE SETTING PAGE
The SEQUENCE MODE SETTING PAGE is the PAGE for setting each PROGRAM condition.
Category Description
Sets dispensing duration for each PROGRAM Sets the dispensing volume for each PROGRAM
Sets the number of PROGRAMs to be used
Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
Selects the PROGRAM to configure
When the dispensing signal is ON in SEQUENCE MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.5 BARREL SETTING PAGE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 40/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. SEQUENCE MODE SETTING PAGE
The SEQUENCE MODE SETTING PAGE is the PAGE for setting each PROGRAM condition.
Category Description
Sets dispensing duration for each PROGRAM Sets the dispensing volume for each PROGRAM
Sets the number of PROGRAMs to be used Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
Selects the PROGRAM to configure
When the dispensing signal is ON in SEQUENCE MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.5 BARREL SETTING PAGE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 40/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. SEQUENCE MODE SETTING PAGE
The SEQUENCE MODE SETTING PAGE is the PAGE for setting each PROGRAM condition.
Category Description
Sets dispensing duration for each PROGRAM Sets the dispensing volume for each PROGRAM
Sets the number of PROGRAMs to be used Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
Selects the PROGRAM to configure
When the dispensing signal is ON in SEQUENCE MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.5 BARREL SETTING PAGE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 40/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. SEQUENCE MODE SETTING PAGE
The SEQUENCE MODE SETTING PAGE is the PAGE for setting each PROGRAM condition.
Category Description
Sets dispensing duration for each PROGRAM Sets the dispensing volume for each PROGRAM
Sets the number of PROGRAMs to be used Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
Selects the PROGRAM to configure
When the dispensing signal is ON in SEQUENCE MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME
7.5 BARREL SETTING PAGE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 39/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until the next
Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
The dispensing operation will be repeated based on the set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME 7.4.4 SEQUENCE MODE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 39/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until the next
Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
The dispensing operation will be repeated based on the set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME 7.4.4 SEQUENCE MODE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 39/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until the next
Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
The dispensing operation will be repeated based on the set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME 7.4.4 SEQUENCE MODE
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 39/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 29. INTERVAL MODE SETTING PAGE
The INTERVAL MODE SETTING PAGE is the PAGE to configure the repeated dispensing conditions.
Category Description
Sets the dispensing duration
Sets the dispensing volume
Shows the wait time after one dispensing operation until the next
Sets the number of SUCKBACK steps
→ If the number of SUCKBACK steps is set, the suckback time will be determined and displayed based on the set Nano Pen capacity.
The dispensing operation will be repeated based on the set dispensing conditions for the number of CYCLEs indicated.
When the dispensing signal is ON in INTERVAL MODE, the Nano Pen will wait until the duration specified in ON DELAY before commencing the dispensing.
MAX (cc/sec) → Displays the maximum speed of the Nano Pen based on the set Barrel capacity
SV (cc/sec) → Displays the set TIME and VOLUME as speed values
MIN (sec) → Displays the minimum number of seconds that can be changed based on the set VOLUME MAX (cc) → Displays the maximum VOLUME that can be
changed based on the set TIME 7.4.4 SEQUENCE MODE
Instrukcja obsługi i instalacji
Rysunek 30. STRONA USTAWIEŃ STRZYKAWKI
Rysunek 30. Strona ustawień sygnału
8.5 STRONA USTAWIEŃ STRZYKAWKI
8.6 STRONA USTAWIEŃ SYGNAŁU
KATEGORIA
KATEGORIA
strzykawka o poj. 3 cm3
Wł./wył. dozowania przy użyciu przełącznika SHOT - na panelu przednim kontrolera DA 1000V.
3 CC
SHOT 5 CC
FOOT
10 CC strzykawka o poj. 10 cm3
EXTERNAL Wł./Wył. dozowania przez ZEWNĘTRZNY PRZEŁACZNIK.
strzykawka o poj. 5 cm3
Wł./wył. dozowania przy użyciu PRZEŁACZNIKA NOŻNEGO - podłączonego do kontrolera DA 1000V.
30 CC strzykawka o poj. 30 cm3 OPIS
DESCRIPTION
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 41/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Figure 30. Setting : Barrel PAGE
This is the PAGE to configure the Barrel capacity according to the Nano Pen capacity.
Category Description
3 CC BARREL 3 CC setting 5 CC BARREL 5 CC setting 10 CC BARREL 10 CC setting 30 CC BARREL 30 CC setting
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 42/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.6 SETTING : SIGNAL PAGE
Figure 31. Setting : SIGNAL PAGE
Sets the Dispensing Mode for the NPC-10.
Category Description
SHOT Enable/disable the SHOT SWITCH for dispensing on the NPC-10 front panel
FOOT Enable/disable the FOOT SWITCH for dispensing on the NPC-10 rear panel
EXTERNAL Enable/disable the External INPUT EXTERNAL SHOT for dispensing
Strona ustawień sygnału to strona do określenia sposobu przekazywania sygnału do urządzenia.
Strona ustawień sygnału to strona do określenia sposobu przekazywania sygnału do urządzenia.
STR. 35
Rysunek 32. Strona ustawień ETC
8.7 STRONA USTAWIEŃ ETC
KATEGORIA
Ustawieni daty: ROK/MIESIĄC/DZIEŃ yy
hh
PWD Funkcja zmiany hasła (nieużywana)
Ustawienie czasu: GODZINA/MINUTA/SEKUNDA
ID Ustawienie identyfikatora komunikacji RS-485
MAX step/sec Ustawienie maksymalnej liczby kroków na sekundę dla silnika i wyświetlenie:
> Prędkości (cm3/s)
> Dystansu (mm/s) OPIS
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 43/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.7 SETTING : ETC PAGE
Figure 32. SETTING : ETC PAGE
Category Description
yy Date Setting section, YEAR / MONTH / DAY
hh Time Setting section, HOUR / MINUTE / SECOND
PWD Passcode change function (Not used)
ID Comm. RS-485 communication ID setting
MAX step/sec
Setting the maximum Steps per second for the Motor and → Speed (cc/sec)
→ Distance (mm/sec) are displayed
Instrukcja obsługi i instalacji
Rysunek 33. Strona alarmu
8.8 STRONA ALARMU
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 44/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.8 ALARM PAGE
Figure 33. ALARM PAGE
Category Description
EMERGENCY If the external INPUT EMERGENCY signal is ON, all operations of the NPC-10 will stop.