Rysunek 21. TRYB USTALONY (STDY)
8.1.2 TRYB USTALONY (STDY)
KATEGORIA
Wyświetla objętość dozowania podczas rozładowywania VOLUME
TIME SPEED SUCKBACK
COUNT
Pokazuje czas, który upłynął do dozowania podczas dozowania Wyświetla ustawioną prędkość dozowania
Pokazuje ustawioną liczbę kroków pracy wstecznej
- Pokazuje liczbę dozowań wykonanych w TRYBIE STAŁYM po zakończeniu ostatniej wymiany strzykawki.
- Wartość COUNT nie wzrośnie, jeśli tryb dozowania zostanie zmieniony.
- Wartość jest resetowana po wymianie strzykawki.
OPIS
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 30/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.1.2 STEADY MODE
Steady Mode is a Dispensing Mode where discharge is continuously executed at a set SPEED, and it is mainly used for Line Dispensing a certain amount.
10cc
TIME S TDY INTV S EQ
cc
COUNT
S UCKBACK cc/sec
sec
2019.01.21 14:59:59
Figure 21. STEADY MODE
Category Description
VOLUME Displays the dispensing volume when discharging TIME Shows the elapsed time for dispensing when dispensing SPEED Displays the set Dispensing SPEED
SUCKBACK Shows the set number of SUCKBACK steps COUNT
- Shows the number of dispenses executed in STEADY MODE after completion of the last Barrel Replacement.
- COUNT value does not increase if Dispensing Mode is changed.
- Value is reset after Barrel Replacement.
Tryb ustalony jest trybem dozowania, w którym rozładowanie jest wykonywane w sposób ciągły z ustaloną prędkością (SPE-ED) i jest używany głównie do dozowania liniowego określonej ilości.
STR. 25
Rysunek 22. Tryb Interwału
8.1.3 TRYB INTERWAŁU
KATEGORIA
Pokazuje ustawioną objętość dozowania VOLUME
TIME
SPEED SUCKBACK
TOTAL CH COUNT
Wyświetla ustawiony czas dozowania (ON) Wyświetla ustawiony czas bezczynności (OFF)
Pokazuje wartość PRĘDKOŚCI zgodnie z objętością dozowania i czasem trwania Pokazuje liczbę kroków wstecz
Pokazuje liczbę wykonanych dozowań
- Wyświetla bieżący numer zliczania podczas dozowania w TRYBIE INTERWAŁOWYM.
- Wartość COUNT wzrasta o ustawioną liczbę TOTAL CH gdy sygnał dozowania jest WŁ.
OPIS
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 31/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.1.3 INTERVAL MODE
Interval Mode is a Dispensing Mode used to consecutively dispense in Time Mode.
When selected, the equipment alternates between Dispensing ON/OFF, and during the ON signal, material will be dispensed according to the set TOTAL CH. Additionally, the INTERVAL MODE will stop if the dispensing signal is provided once again while INTERVAL MODE is in progress.
TIME S TDY INTV S EQ
TOTAL CH.
10cc
cc
COUNT
S UCKBACK cc/sec
sec
ON OFF
2019.01.21 14:59:59
Figure 22. Interval Mode
Category Description
VOLUME Shows the set dispensing volume TIME Displays the set dispensing (ON) time
Displays the set idle (OFF) time
SPEED Shows the SPEED value according to the dispensing volume and duration
SUCKBACK Shows the set number of SUCKBACK steps COUNT
- Displays the current count number when dispensing in INTERVAL MODE.
- COUNT value increases by the set number of TOTAL CH. when the dispensing signal is ON.
TOTAL CH. - Shows the number of dispenses executed.
7.1.4 SEQUENCE MODE
Tryb interwału to tryb dozowania stosowany przy kolejnym dozowaniu w Trybie Czasu.
Po jego wybraniu urządzenie przełącza się między dozowaniem WŁ. / WYŁ., podczas sygnału WŁ. materiał zostanie wydany zgodnie z ustawieniem TOTAL CH. Dodatkowo TRYB INTERWAŁU zatrzyma się, jeśli sygnał dozowania zostanie podany ponownie, podczas pracy TRYBU INTERWAŁU.
- Wyświetla numer PROGRAMU aktualnie planowanego do dozowania.
- Po zakończeniu aktualnego ROGRAMU dozowania wartość PROGRAMU przechodzi do następnej ustawionej wartości.
- Użytkownik może zmienić numer PROGRAMU, dotykając odpowiedniego obszaru PROGRAMU
Instrukcja obsługi i instalacji
Rysunek 23, Tryb sekwencji
8.1.4 TRYB SEKWENCJI
KATEGORIA
Wyświetla ustawioną objętość dozowania dla skonfigurowanego PROGRAMU VOLUME
TIME
SPEED
SUCKBACK
TOTAL CH PROGRAM
Wyświetla ustawiony czas dozowania dla skonfigurowanego PROGRAMU
Wyświetla wartość PRĘDKOŚCI zgodnie z ustawioną objętością dozowania i czasem trwania skonfigurowanego PROGRAMU
Wyświetla ilość kroków wstecz skonfigurowanych dla PROGRAMU
- Wyświetla całkowitą liczbę kanałów ustawionych w Trybie Sekwencji, - TOTAL CH - liczba skonfigurowanych kanałów (maksymalnie 16) OPIS
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 32/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
Sequence Mode is a Dispensing Mode where up to 16 desired condition values can be configured, and each PROGRAM sequentially dispenses the material according to the various conditions.
10cc
TIME S TDY INTV S EQ
TOTAL CH.
cc
PROGRAM
S UCKBACK cc/sec
sec
2019.01.21 14:59:59
Figure 23. Sequence Mode
Category Description
VOLUME Displays the set dispensing volume for the configured PROGRAM TIME Displays the set dispensing time for the configured PROGRAM SPEED Displays the SPEED value according to the set dispensing volume and
duration for the configured PROGRAM
SUCKBACK Displays the number of SUCKBACK steps for the configured PROGRAM
PROGRAM
- Displays the PROGRAM number currently planned for dispensing.
- When the current PROGRAM dispensing is complete, the PROGRAM value is increased to the next value.
- The user can change the PROGRAM number by touching the corresponding PROGRAM area.
TOTAL CH. - Displays the total channels set in Sequence Mode.
- TOTAL CH.: number of configured channels (maximum 16)
Tryb sekwencji to tryb dozowania, w którym można skonfigurować do 16 pożądanych wartości warunków, a każdy PRO-GRAM kolejno dozuje materiał zgodnie z zadanymi warunkami.
STR. 27
Rysunek 24. Wymiana strzykawki
8.2 WYMIANA STRZYKAWKI
KATEGORIA
Jest to funkcja automatycznego powrotu do pozycji ORIGIN (pozycja początkowa) po wymianie strzykawki.
> Funkcja AUTO BACK zatrzyma się po naciśnięciu przycisku SHOT
Wyświetlany, gdy bieżąca pozycja DA 1000 V znajduje się w pozycji ORIGIN
Przycisk używany po zakończeniu wymiany strzykawki
> Gdy przycisk CHANGED jest włączony, wartość COUNT stosowana do każd-ego trybu dozowania jest resetowana.
Wskazuje, że kierunek pracy DA1000 V jest FORWARD (do przodu)
Wskazuje, że kierunek DA 1000V jest BACKWARD (do tyłu)
Prędkość roboczą DA 1000 V można regulować, wprowadzając konkretną wartość.
OPIS
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 33/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.2 CHANGE BARREL PAGE
Figure 24. Change Barrel PAGE
Category Description
This is a function to automatically return to the ORIGIN Position (initial position) when the barrel is replaced.
→ The AUTO BACK function will stop if the SHOT button is pressed.
Displayed when the current Nano Pen position is in the ORIGIN Position
Button used when Barrel Change is complete
→ When the CHANGED button is turned ON, the COUNT value applied to each dispensing mode is reset.
Indicates that the direction of the Nano Pen is FORWARD → Opposite of BACKWARD
Indicates that the direction of the Nano Pen is BACKWARD → Opposite of FORWARD
The Nano Pen Operation Speed can be adjusted by inserting a value.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 33/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.2 CHANGE BARREL PAGE
Figure 24. Change Barrel PAGE
Category Description
This is a function to automatically return to the ORIGIN Position (initial position) when the barrel is replaced.
→ The AUTO BACK function will stop if the SHOT button is pressed.
Displayed when the current Nano Pen position is in the ORIGIN Position
Button used when Barrel Change is complete
→ When the CHANGED button is turned ON, the COUNT value applied to each dispensing mode is reset.
Indicates that the direction of the Nano Pen is FORWARD → Opposite of BACKWARD
Indicates that the direction of the Nano Pen is BACKWARD → Opposite of FORWARD
The Nano Pen Operation Speed can be adjusted by inserting a value.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 33/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.2 CHANGE BARREL PAGE
Figure 24. Change Barrel PAGE
Category Description
This is a function to automatically return to the ORIGIN Position (initial position) when the barrel is replaced.
→ The AUTO BACK function will stop if the SHOT button is pressed.
Displayed when the current Nano Pen position is in the ORIGIN Position
Button used when Barrel Change is complete
→ When the CHANGED button is turned ON, the COUNT value applied to each dispensing mode is reset.
Indicates that the direction of the Nano Pen is FORWARD → Opposite of BACKWARD
Indicates that the direction of the Nano Pen is BACKWARD → Opposite of FORWARD
The Nano Pen Operation Speed can be adjusted by inserting a value.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 33/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.2 CHANGE BARREL PAGE
Figure 24. Change Barrel PAGE
Category Description
This is a function to automatically return to the ORIGIN Position (initial position) when the barrel is replaced.
→ The AUTO BACK function will stop if the SHOT button is pressed.
Displayed when the current Nano Pen position is in the ORIGIN Position
Button used when Barrel Change is complete
→ When the CHANGED button is turned ON, the COUNT value applied to each dispensing mode is reset.
Indicates that the direction of the Nano Pen is FORWARD → Opposite of BACKWARD
Indicates that the direction of the Nano Pen is BACKWARD → Opposite of FORWARD
The Nano Pen Operation Speed can be adjusted by inserting a value.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 33/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.2 CHANGE BARREL PAGE
Figure 24. Change Barrel PAGE
Category Description
This is a function to automatically return to the ORIGIN Position (initial position) when the barrel is replaced.
→ The AUTO BACK function will stop if the SHOT button is pressed.
Displayed when the current Nano Pen position is in the ORIGIN Position
Button used when Barrel Change is complete
→ When the CHANGED button is turned ON, the COUNT value applied to each dispensing mode is reset.
Indicates that the direction of the Nano Pen is FORWARD → Opposite of BACKWARD
Indicates that the direction of the Nano Pen is BACKWARD → Opposite of FORWARD
The Nano Pen Operation Speed can be adjusted by inserting a value.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 33/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
7.2 CHANGE BARREL PAGE
Figure 24. Change Barrel PAGE
Category Description
This is a function to automatically return to the ORIGIN Position (initial position) when the barrel is replaced.
→ The AUTO BACK function will stop if the SHOT button is pressed.
Displayed when the current Nano Pen position is in the ORIGIN Position
Button used when Barrel Change is complete
→ When the CHANGED button is turned ON, the COUNT value applied to each dispensing mode is reset.
Indicates that the direction of the Nano Pen is FORWARD → Opposite of BACKWARD
Indicates that the direction of the Nano Pen is BACKWARD → Opposite of FORWARD
The Nano Pen Operation Speed can be adjusted by inserting a value.
Instrukcja obsługi i instalacji
KATEGORIA
> Po dotknięciu pola tekstowego SPEED ustawienie zmieni się na STEP.
DA 1000 V można obsługiwać z wybraną liczbą kroków (STEP), wprowadzając liczbę operacji DA 1000V.
> dozownik będzie działać w oparciu o wartość prędkości ustawioną w polu tekstowym SPEED.
> Po dotknięciu pola tekstowego STEP ustawienie ponownie zmieni się na SPEED.
Prędkość (SPEED) jest wyświetlana jako wartości liczbowe dla każdej jednostki prędkości.
Prędkość roboczą DA 1000V można zwiększyć lub zmniejszyć.
> Lewy przycisk: zmniejsz, prawy przycisk: zwiększ
Wyświetla liczbę kroków operacyjnych DA 1000 V.
To okno alarmu pojawia się, gdy włączony jest alarm kontrolera DA 1000V.
> Przejdź do strony ALARM PAGE i sprawdź status alarmu.
OPIS
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 34/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
→ If the SPEED text box is touched, the setting will switch to STEP.
The Nano Pen can be operated with the desired number of STEPs by inserting the number of Nano Pen operations.
→ The pen will operate based on the SPEED value set in the SPEED text box.
→ If the STEP text box is touched, the setting will change back to SPEED.
The SPEED is displayed as numerical values for each speed unit.
The operating speed of the Nano Pen can be increased or decreased.
→ Left button: decrease, Right button: increase
Displays the number of Nano Pen operation steps.
This is an alarm window that appears when NPC-10 alarm is on.
→ Go to the ALARM PAGE and check the alarm status.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 34/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
→ If the SPEED text box is touched, the setting will switch to STEP.
The Nano Pen can be operated with the desired number of STEPs by inserting the number of Nano Pen operations.
→ The pen will operate based on the SPEED value set in the SPEED text box.
→ If the STEP text box is touched, the setting will change back to SPEED.
The SPEED is displayed as numerical values for each speed unit.
The operating speed of the Nano Pen can be increased or decreased.
→ Left button: decrease, Right button: increase
Displays the number of Nano Pen operation steps.
This is an alarm window that appears when NPC-10 alarm is on.
→ Go to the ALARM PAGE and check the alarm status.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 34/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
→ If the SPEED text box is touched, the setting will switch to STEP.
The Nano Pen can be operated with the desired number of STEPs by inserting the number of Nano Pen operations.
→ The pen will operate based on the SPEED value set in the SPEED text box.
→ If the STEP text box is touched, the setting will change back to SPEED.
The SPEED is displayed as numerical values for each speed unit.
The operating speed of the Nano Pen can be increased or decreased.
→ Left button: decrease, Right button: increase
Displays the number of Nano Pen operation steps.
This is an alarm window that appears when NPC-10 alarm is on.
→ Go to the ALARM PAGE and check the alarm status.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 34/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
→ If the SPEED text box is touched, the setting will switch to STEP.
The Nano Pen can be operated with the desired number of STEPs by inserting the number of Nano Pen operations.
→ The pen will operate based on the SPEED value set in the SPEED text box.
→ If the STEP text box is touched, the setting will change back to SPEED.
The SPEED is displayed as numerical values for each speed unit.
The operating speed of the Nano Pen can be increased or decreased.
→ Left button: decrease, Right button: increase
Displays the number of Nano Pen operation steps.
This is an alarm window that appears when NPC-10 alarm is on.
→ Go to the ALARM PAGE and check the alarm status.
NANO PENNANOPEN Operation Manual Doc. Rev 0
2019/7/2 34/47 Copyright © 2019 by TAEHA CORP. All Rights Reserved
→ If the SPEED text box is touched, the setting will switch to STEP.
The Nano Pen can be operated with the desired number of STEPs by inserting the number of Nano Pen operations.
→ The pen will operate based on the SPEED value set in the SPEED text box.
→ If the STEP text box is touched, the setting will change back to SPEED.
The SPEED is displayed as numerical values for each speed unit.
The operating speed of the Nano Pen can be increased or decreased.
→ Left button: decrease, Right button: increase
Displays the number of Nano Pen operation steps.
This is an alarm window that appears when NPC-10 alarm is on.
→ Go to the ALARM PAGE and check the alarm status.
STR. 29
Rysunek 25. Meny główne
Rysunek 26. USTAWIENIA TRYB STRONY